Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

XML configuration parameters for IP address assignment and adding manual routes

Assign IP addresses to all interfaces in the network

Avoid using the same address and raise an error if not possible

Avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces

Add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)

Add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)

Add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)

Add direct routes towards local network members (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)

Add routes towards remote (non-directly-connected) destinations via a gateway (used only if addStaticRoutes is true)

Optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)

Add manual routes from the XML configuration; independent of addStaticRoutes

Recalculate static routes if an interface goes down/up or a carrier is lost/back

Print extracted network topology to the module output

Print recognized network links to the module output

Print assigned IP addresses for all interfaces to the module output

Print configured and optimized routing tables for all nodes to the module output

Write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)

Maximum sending power used for this network (in mW)

Signal attenuation threshold (in dBm)

Path loss coefficient

Base carrier frequency of all the channels (in Hz)

Number of radio channels (frequencies)

JSON array: [{coreNetwork, ue, drbId, profile, mappedQfis, filters, lcg, rlcMode, legs, isDefault, suppressSdapHeader, rohc, gbr, packetDelayBudget, packetErrorRate, qosPriorityLevel}, ...]; see banner comment for details

JSON map of named field groups referenced by the staticDrbs entries' "profile" field, e.g. {voice: {rlcMode: "UM", gbr: true, ...}, ...}; see banner comment

QFI classification rules, delivered to their evaluation sites (see banner comment)

JSON array of uplink QFI-assignment rules [{ue, filter, qfi|dscpAsQfi}, ...], delivered to the UEs' QoS-flow classifiers; [] = classify nothing

QoS-derived RAN defaults for definitions that do not state rlcMode/lcg themselves (operator policy, not spec-mandated: 3GPP standardizes the QoS characteristics, the RAN chooses what to make of them)

Lcg derivation: qosPriorityLevel < bounds[k] -> LCG k, else LCG 3; strictly ascending, one bound between each pair of adjacent LCGs

Header compression policy: definitions naming one of these profiles get "rohc: true" unless they state rohc themselves, on IP sessions; default: the voice bearers

Carrier Frequency (GHz)

Number of bands for this channel

Numerology index

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

TODO @signal, @statistic

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Initialization stage for the setup command

Create new network namespaces under /var/run/netns/ (Linux only)

Name of the host OS network namespace (optional) (Linux only)

A host OS system command

A host OS system command

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of sibling module names to listen on

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

The node's Ethernet session bridge (see EthernetSessionBridge), if it has one

The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. "2001:db8:5::/64" or "10.5.0.0/16"; empty = the node anchors no Unstructured session (see the main comment)

The application server the Unstructured sessions' uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix

The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions

The UDP port the node receives the Unstructured sessions' downlink on, and sends their uplink from; must be set for Unstructured sessions

The router's address on every session's link

Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)

Cur Hop Limit in the Router Advertisements (0 = unspecified)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

The bridge's interface table, which the session ports are registered in

The bridge's MAC table, flushed of a released session's port

The module type of the session ports

Display string of the session ports (their place in the bridge's layout)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

TODO @signal, @statistic

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Initialization stage for the setup command

Create new network namespaces under /var/run/netns/ (Linux only)

Name of the host OS network namespace (optional) (Linux only)

A host OS system command

A host OS system command

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of sibling module names to listen on

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

The node's Ethernet session bridge (see EthernetSessionBridge), if it has one

The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. "2001:db8:5::/64" or "10.5.0.0/16"; empty = the node anchors no Unstructured session (see the main comment)

The application server the Unstructured sessions' uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix

The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions

The UDP port the node receives the Unstructured sessions' downlink on, and sends their uplink from; must be set for Unstructured sessions

The router's address on every session's link

Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)

Cur Hop Limit in the Router Advertisements (0 = unspecified)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

The bridge's interface table, which the session ports are registered in

The bridge's MAC table, flushed of a released session's port

The module type of the session ports

Display string of the session ports (their place in the bridge's layout)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module

The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)

Enables continuous update of the subject module's position by modifying its display string

The minimum x position of the constraint area. It is unconstrained by default (negative infinity)

The minimum y position of the constraint area. It is unconstrained by default (negative infinity)

The minimum z position of the constraint area. It is unconstrained by default (negative infinity)

The maximum x position of the constraint area. It is unconstrained by default (positive infinity)

The maximum y position of the constraint area. It is unconstrained by default (positive infinity)

The maximum z position of the constraint area. It is unconstrained by default (positive infinity)

Enables one-time initialization from the subject module's display string

Enables continuous update from the subject module's display string for dragging and rotating it

The minimum X-coordinate of the area constraint, unconstrained by default

The minimum Y-coordinate of the area constraint, unconstrained by default

The maximum X-coordinate of the area constraint, unconstrained by default

The maximum Y-coordinate of the area constraint, unconstrained by default

Interval for sending broadcast messages (used for handover or DAS)

Type of eNodeB (MICRO / MACRO) - valid only for eNodeBs

Number of sub-carriers per RB in DL

Number of sub-carriers per RB in UL

Number of OFDM symbols per slot in DL

Number of OFDM symbols per slot in UL

Number of pilot Resource Elements per RB in DL

Number of pilot Resource Elements per RB in UL

Number of signaling symbols for each Resource Block in DL

Number of signaling symbols for each Resource Block in UL

Number of preferred bands to use (relevant only in PREFERRED mode)

One of "eNBStatsCollector", "gNBStatsCollector", "ueStatsCollector", "NrUeStatsCollector"

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)

Delayed ACK algorithm (RFC 1122) enabled/disabled

Nagle's algorithm (RFC 896) enabled/disabled

Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)

Increased Initial Window (RFC 3390) enabled/disabled

Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)

Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)

Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)

Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)

Maximum Segment Size (header option). Default 536 per RFC 1122.

Maximum Segment Lifetime

Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing

Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit...

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

True if willing to use ECN

A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)

Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled

Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Comma-separated list of addresses

Port number to listen on

Server address (may be symbolic)

Port number to connect to

Time the first session begins

Number of requests sent per session

Length of a request (bytes)

Time gap between requests

Time to wait between the last message sent and abort

If the connection breaks, waits this much before trying to reconnect

Echoes received packages when true

0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST

For PR-SCTP

NO_RESET=5, RESET_OUTGOING=6, RESET_INCOMING=7, RESET_BOTH=8, SSN_TSN=9

Time of finishing sending, negative values mean forever

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Comma-separated list of addresses

Port number to listen on

Echoes received packages when true

Number of requests sent per session

Length of a request (bytes)

Time gap between requests

Time to wait between last message sent and abort

0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST

For PR-SCTP

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

RFC4960=0

0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks

Limit for SWS

For flow control

For flow control

For flow control

For flow control

SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154

CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

TODO @signal, @statistic

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Initialization stage for the setup command

Create new network namespaces under /var/run/netns/ (Linux only)

Name of the host OS network namespace (optional) (Linux only)

A host OS system command

A host OS system command

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of sibling module names to listen on

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)

Delayed ACK algorithm (RFC 1122) enabled/disabled

Nagle's algorithm (RFC 896) enabled/disabled

Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)

Increased Initial Window (RFC 3390) enabled/disabled

Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)

Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)

Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)

Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)

Maximum Segment Size (header option). Default 536 per RFC 1122.

Maximum Segment Lifetime

Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing

Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit...

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

True if willing to use ECN

A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)

Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled

Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Local address; may be left empty ("")

localPort number to listen on

If not -1, set the Type of Service (IPv4) / Traffic Class (IPv6) field of sent packets to this value

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

TODO @signal, @statistic

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Initialization stage for the setup command

Create new network namespaces under /var/run/netns/ (Linux only)

Name of the host OS network namespace (optional) (Linux only)

A host OS system command

A host OS system command

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of sibling module names to listen on

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module

When true packets are serialized into a sequence of bytes before sending out

Extra time after lifecycle stop operation finished

Timeout value for lifecycle stop operation

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

The node's Ethernet session bridge (see EthernetSessionBridge), if it has one

The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. "2001:db8:5::/64" or "10.5.0.0/16"; empty = the node anchors no Unstructured session (see the main comment)

The application server the Unstructured sessions' uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix

The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions

The UDP port the node receives the Unstructured sessions' downlink on, and sends their uplink from; must be set for Unstructured sessions

The router's address on every session's link

Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)

Cur Hop Limit in the Router Advertisements (0 = unspecified)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

The bridge's interface table, which the session ports are registered in

The bridge's MAC table, flushed of a released session's port

The module type of the session ports

Display string of the session ports (their place in the bridge's layout)

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Module path to the InterfaceTable module

Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default

Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default

Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Available policies: "MecHostBased", "MecServiceBased", "AvailableResourcesBased"

To be used with the MecHostBased policy

Times to simulate lifecycle operations

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to display IP addresses on links

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

Whether to log packets on the module output

Specifies if zero length packets are recorded or not

Specifies if converting packets to link type is allowed or not

The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"

Maximum number of bytes to record per packet

Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).

Enable dump of frames with hasBitError

Space-separated list of outbound packet signals to subscribe to

Space-separated list of inbound packet signals to subscribe to

Space-separated list of protocol names as defined in the Protocol class

Which packets are considered, matches all packets by default

Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"

Flush the pcapFile after each write to ensure that all packets are captured in case of a crash

Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information

The path to the InterfaceTable module