MultiMecHost¶

Package: simu5g.simulations.nr.mec.multiMecHost

network MultiMecHost

Two gNodeB cells, each on an intermediate Upf of its own with a MecHost hung off it, so every cell has its own MEC host. Both intermediate Upf nodes meet at the anchor Upf, which carries the Ualcmp and, behind it, the MecOrchestrator. An X2 link joins the two gNodeBs. numUe NrUe terminals attach, and numBgCells BackgroundCell cells can be added as interferers.

Usage diagram¶

Parameters¶

Name	Type	Default value	Description
numUe	int	1
numBgCells	int	0

Properties¶

Name	Value	Description
display	i=block/network2;bgb=1088,678;bgi=background/pisa

Unassigned submodule parameters¶

Name	Type	Default value	Description
channelControl.pMax	double	20mW	Maximum sending power used for this network (in mW)
channelControl.sat	double	-110dBm	Signal attenuation threshold (in dBm)
channelControl.alpha	double	2	Path loss coefficient
channelControl.carrierFrequency	double	2.4GHz	Base carrier frequency of all the channels (in Hz)
channelControl.numChannels	int	1	Number of radio channels (frequencies)
routingRecorder ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
routingRecorder ↗.enabled	bool	true
routingRecorder ↗.logfile	string	“${resultdir}/${configname}-#${runnumber}.rt”
configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
configurator ↗.minLinkWeight	double	1E-3
configurator ↗.configureIsolatedNetworksSeparatly	bool	false
configurator ↗.config	xml	xml(“<config><interface hosts=’**’ address=’10.x.x.x’ netmask=’255.x.x.x’/></config>”)	XML configuration parameters for IP address assignment and adding manual routes
configurator ↗.assignAddresses	bool	true	Assign IP addresses to all interfaces in the network
configurator ↗.assignUniqueAddresses	bool	true	Avoid using the same address and raise an error if not possible
configurator ↗.assignDisjunctSubnetAddresses	bool	true	Avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator ↗.addStaticRoutes	bool	true	Add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator ↗.addDefaultRoutes	bool	true	Add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator ↗.addSubnetRoutes	bool	true	Add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator ↗.addDirectRoutes	bool	true	Add direct routes towards local network members (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator ↗.addRemoteRoutes	bool	true	Add routes towards remote (non-directly-connected) destinations via a gateway (used only if addStaticRoutes is true)
configurator ↗.optimizeRoutes	bool	true	Optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator ↗.addManualRoutes	bool	true	Add manual routes from the XML configuration; independent of addStaticRoutes
configurator ↗.updateRoutes	bool	false	Recalculate static routes if an interface goes down/up or a carrier is lost/back
configurator ↗.dumpTopology	bool	false	Print extracted network topology to the module output
configurator ↗.dumpLinks	bool	false	Print recognized network links to the module output
configurator ↗.dumpAddresses	bool	false	Print assigned IP addresses for all interfaces to the module output
configurator ↗.dumpRoutes	bool	false	Print configured and optimized routing tables for all nodes to the module output
configurator ↗.dumpConfig	string	“”	Write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
binder.blerShift	int	0
binder.maxDataRatePerRb	double	1.16Mbps
binder.printTrafficGeneratorConfig	bool	false
coreControl.binderModule	string	“binder”
coreControl.bearerConfiguratorModule	string	“bearerConfigurator”
bearerConfigurator.binderModule	string	“binder”
bearerConfigurator.staticDrbs	object	[]	JSON array: [{coreNetwork, ue, drbId, profile, mappedQfis, filters, lcg, rlcMode, legs, isDefault, suppressSdapHeader, rohc, gbr, packetDelayBudget, packetErrorRate, qosPriorityLevel}, …]; see banner comment for details
bearerConfigurator.onDemandDrbs	object	[ // JSON array, staticDrbs schema minus “drbId” (and “ue” optional): bearers created when traffic first matches them; the default value lets both stack kinds run unauthored; see banner comment for details {coreNetwork: “epc”, filters: [“VoIP”], lcg: 0, rlcMode: “UM”}, {coreNetwork: “epc”, filters: [“gaming”], lcg: 2, rlcMode: “UM”}, {coreNetwork: “epc”, filters: [“VoDPacket”, “VoDFinishPacket”], lcg: 1, rlcMode: “UM”}, {coreNetwork: “epc”, isDefault: true, lcg: 3, rlcMode: “UM”}, {coreNetwork: “5gc”, isDefault: true, suppressSdapHeader: true, lcg: 3, rlcMode: “UM”} ]
bearerConfigurator.drbProfiles	object	{}	JSON map of named field groups referenced by the staticDrbs entries’ “profile” field, e.g. {voice: {rlcMode: “UM”, gbr: true, …}, …}; see banner comment
bearerConfigurator.dlQfiRules	object	[{dscpAsQfi: true}]	JSON array of downlink QFI-assignment rules [{node, filter, qfi\|dscpAsQfi}, …], delivered to the traffic flow filters at core-network tunnel entries; first match wins per site
bearerConfigurator.ulQfiRules	object	[]	JSON array of uplink QFI-assignment rules [{ue, filter, qfi\|dscpAsQfi}, …], delivered to the UEs’ QoS-flow classifiers; [] = classify nothing
bearerConfigurator.amPerThreshold	double	1e-4	rlcMode derivation: a definition whose QoS profile has packetErrorRate <= this gets “AM”, else “UM”
bearerConfigurator.lcgPriorityBounds	object	[25, 50, 75]	Lcg derivation: qosPriorityLevel < bounds[k] -> LCG k, else LCG 3; strictly ascending, one bound between each pair of adjacent LCGs
bearerConfigurator.rohcForDrbProfiles	object	[“5qi-1”, “qci-1”]	Header compression policy: definitions naming one of these profiles get “rohc: true” unless they state rohc themselves, on IP sessions; default: the voice bearers
carrierAggregation.componentCarrier.binderModule	string	“binder”
carrierAggregation.componentCarrier.carrierFrequency	double	2GHz	Carrier Frequency (GHz)
carrierAggregation.componentCarrier.numBands	int	6	Number of bands for this channel
carrierAggregation.componentCarrier.numerologyIndex	int	0	Numerology index
carrierAggregation.componentCarrier.useTdd	bool	false	TDD slot format index values in the range [0,61], according to 3GPP TS38.213 THIS IS TO BE DONE int tddSlotFormatIndex = default(-1); // -1 stands for FDD
carrierAggregation.componentCarrier.tddNumSymbolsDl	int	7
carrierAggregation.componentCarrier.tddNumSymbolsUl	int	7
upf.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.status ↗.initialStatus	string	“UP”	Initial status of the network node
upf.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.environment ↗.initStage	int	0	Initialization stage for the setup command
upf.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
upf.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
upf.environment ↗.setupCommand	string	“”	A host OS system command
upf.environment ↗.teardownCommand	string	“”	A host OS system command
upf.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
upf.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
upf.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.cb ↗.forwardServiceRegistration	bool	true
upf.cb ↗.forwardProtocolRegistration	bool	true
upf.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.bl ↗.forwardServiceRegistration	bool	true
upf.bl ↗.forwardProtocolRegistration	bool	true
upf.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
upf.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ethernet ↗.fcsMode	string	“declared”
upf.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
upf.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
upf.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.li ↗.forwardServiceRegistration	bool	true
upf.li ↗.forwardProtocolRegistration	bool	true
upf.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.lo ↗.lo ↗.mtu	int	4470B
upf.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.wlan ↗.agent ↗.mibModule	string
upf.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
upf.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
upf.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
upf.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
upf.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
upf.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
upf.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
upf.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
upf.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
upf.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
upf.wlan ↗.mgmt ↗.mibModule	string
upf.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
upf.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
upf.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
upf.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
upf.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
upf.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
upf.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
upf.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
upf.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
upf.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
upf.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
upf.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
upf.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
upf.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
upf.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
upf.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
upf.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
upf.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
upf.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
upf.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
upf.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
upf.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
upf.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
upf.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
upf.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
upf.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
upf.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
upf.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.ds ↗.mibModule	string
upf.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.wlan ↗.mac ↗.tx ↗.rxModule	string
upf.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
upf.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
upf.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
upf.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
upf.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
upf.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
upf.ppp ↗.ppp ↗.mtu	int	4470B
upf.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
upf.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
upf.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.tun ↗.tun ↗.mtu	int	1500B
upf.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.virt ↗.tunnel ↗.interfaceTableModule	string
upf.virt ↗.tunnel ↗.realInterface	string
upf.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
upf.virt ↗.tunnel ↗.address	string	“copy”
upf.virt ↗.tunnel ↗.vlanId	int	-1
upf.virt ↗.tunnel ↗.steal	bool	vlanId != -1
upf.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.configurator ↗.routingTableModule	string
upf.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
upf.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
upf.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
upf.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
upf.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
upf.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
upf.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
upf.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
upf.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
upf.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
upf.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
upf.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
upf.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.igmp ↗.routingTableModule	string
upf.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
upf.ipv4 ↗.igmp ↗.enabled	bool	true
upf.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
upf.ipv4 ↗.igmp ↗.queryInterval	double	125s
upf.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
upf.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
upf.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
upf.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
upf.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
upf.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
upf.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
upf.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
upf.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.icmp ↗.routingTableModule	string
upf.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
upf.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
upf.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
upf.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
upf.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.ip ↗.routingTableModule	string
upf.ipv4 ↗.ip ↗.arpModule	string
upf.ipv4 ↗.ip ↗.icmpModule	string
upf.ipv4 ↗.ip ↗.checksumMode	string	“declared”
upf.ipv4 ↗.ip ↗.timeToLive	int	32
upf.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
upf.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
upf.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
upf.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
upf.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
upf.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
upf.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
upf.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv4 ↗.arp ↗.routingTableModule	string
upf.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
upf.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
upf.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
upf.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
upf.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
upf.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
upf.ipv4 ↗.ipsec ↗.interfaceTableModule	string
upf.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
upf.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
upf.ipv4 ↗.ipsec ↗.spdConfig	xml
upf.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
upf.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
upf.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
upf.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
upf.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
upf.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
upf.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
upf.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
upf.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
upf.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
upf.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
upf.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.configurator ↗.interfaceTableModule	string
upf.ipv6 ↗.configurator ↗.routingTableModule	string
upf.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
upf.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
upf.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
upf.ipv6 ↗.routingTable ↗.forwarding	bool	false
upf.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
upf.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
upf.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
upf.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
upf.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
upf.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
upf.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
upf.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
upf.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
upf.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
upf.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
upf.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
upf.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
upf.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
upf.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
upf.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
upf.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
upf.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
upf.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
upf.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
upf.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
upf.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
upf.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
upf.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
upf.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
upf.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
upf.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
upf.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
upf.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv6 ↗.ipv6 ↗.routingTableModule	string
upf.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
upf.ipv6 ↗.ipv6 ↗.icmpv6Module	string
upf.ipv6 ↗.ipv6 ↗.procDelay	double	0s
upf.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
upf.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.ipsec ↗.interfaceTableModule	string
upf.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
upf.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
upf.ipv6 ↗.ipsec ↗.spdConfig	xml
upf.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
upf.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
upf.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
upf.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
upf.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
upf.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
upf.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
upf.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
upf.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
upf.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
upf.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
upf.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
upf.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
upf.ipv6 ↗.mipv6 ↗.isMobileNode	bool
upf.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
upf.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
upf.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
upf.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
upf.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
upf.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
upf.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
upf.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
upf.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
upf.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
upf.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
upf.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
upf.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
upf.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
upf.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
upf.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
upf.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
upf.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
upf.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
upf.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
upf.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
upf.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
upf.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
upf.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
upf.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
upf.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.nl ↗.forwardServiceRegistration	bool	true
upf.nl ↗.forwardProtocolRegistration	bool	true
upf.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.udp ↗.checksumMode	string	“declared”
upf.udp ↗.defaultMulticastLoop	bool	true
upf.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.tcp ↗.checksumMode	string	“declared”
upf.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
upf.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
upf.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
upf.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
upf.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
upf.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
upf.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
upf.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
upf.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
upf.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
upf.tcp ↗.msl	int	120s	Maximum Segment Lifetime
upf.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
upf.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
upf.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
upf.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
upf.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
upf.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
upf.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
upf.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
upf.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
upf.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.sctp ↗.interfaceTableModule	string
upf.sctp ↗.routingTableModule	string
upf.sctp ↗.checksumMode	string	“declared”
upf.sctp ↗.numGapReports	int	3
upf.sctp ↗.rtoInitial	double	3s
upf.sctp ↗.rtoMin	double	1s
upf.sctp ↗.rtoMax	double	60s
upf.sctp ↗.rtoAlpha	double	0.125
upf.sctp ↗.rtoBeta	double	0.250
upf.sctp ↗.maxBurst	int	4
upf.sctp ↗.maxBurstVariant	string	“maxBurst”
upf.sctp ↗.initialWindow	int	0
upf.sctp ↗.assocMaxRetrans	int	10
upf.sctp ↗.pathMaxRetrans	int	5
upf.sctp ↗.maxInitRetrans	int	8
upf.sctp ↗.sackPeriod	double	200ms
upf.sctp ↗.sackFrequency	int	2
upf.sctp ↗.reactivatePrimaryPath	bool	false
upf.sctp ↗.sendQueueLimit	int	0
upf.sctp ↗.validCookieLifetime	double	10s
upf.sctp ↗.enableHeartbeats	bool	true
upf.sctp ↗.hbInterval	double	30s
upf.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
upf.sctp ↗.nagleEnabled	bool	true
upf.sctp ↗.naglePoint	int	1468
upf.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
upf.sctp ↗.fastRecoverySupported	bool	true
upf.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
upf.sctp ↗.ccModule	int	0	RFC4960=0
upf.sctp ↗.osbWithHeader	bool	false
upf.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
upf.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
upf.sctp ↗.arwnd	int	65535
upf.sctp ↗.swsLimit	int	3000	Limit for SWS
upf.sctp ↗.udpEncapsEnabled	bool	false
upf.sctp ↗.natFriendly	bool	false
upf.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
upf.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
upf.sctp ↗.tellArwnd	bool	false	For flow control
upf.sctp ↗.messageAcceptLimit	int	0	For flow control
upf.sctp ↗.fairStart	double	0s
upf.sctp ↗.fairStop	double	0s
upf.sctp ↗.streamsToPaths	string	“”
upf.sctp ↗.startEndToEndDelay	int	0
upf.sctp ↗.stopEndToEndDelay	int	10
upf.sctp ↗.throughputInterval	double	1
upf.sctp ↗.auth	bool	false
upf.sctp ↗.chunks	string	“”
upf.sctp ↗.padding	bool	false
upf.sctp ↗.addIP	bool	false
upf.sctp ↗.addTime	double	0s
upf.sctp ↗.addAddress	string	“”
upf.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
upf.sctp ↗.packetDrop	bool	false
upf.sctp ↗.sackNow	bool	false
upf.sctp ↗.highSpeedCC	bool	false
upf.sctp ↗.checkSackSeqNumber	bool	false
upf.sctp ↗.nrSack	bool	false
upf.sctp ↗.disableReneging	bool	false
upf.sctp ↗.gapReportLimit	int	100000000
upf.sctp ↗.gapListOptimizationVariant	string	“none”
upf.sctp ↗.smartOverfullSACKHandling	bool	false
upf.sctp ↗.allowQoSTracking	bool	false
upf.sctp ↗.qosTrackingInterval	double	1.0s
upf.sctp ↗.cmtSendAllVariant	string	“normal”
upf.sctp ↗.cmtRetransmissionVariant	string	“normal”
upf.sctp ↗.cmtCUCVariant	string	“normal”
upf.sctp ↗.cmtBufferSplitVariant	string	“none”
upf.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
upf.sctp ↗.cmtUseSFR	bool	true
upf.sctp ↗.cmtUseDAC	bool	true
upf.sctp ↗.cmtUseFRC	bool	true
upf.sctp ↗.cmtSmartT3Reset	bool	true
upf.sctp ↗.cmtSmartFastRTX	bool	true
upf.sctp ↗.cmtSmartReneging	bool	false
upf.sctp ↗.cmtSlowPathRTTUpdate	bool	false
upf.sctp ↗.cmtChunkReschedulingVariant	string	“none”
upf.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
upf.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
upf.sctp ↗.movedChunkFastRTXFactor	double	2.0
upf.sctp ↗.cmtSackPath	string	“standard”
upf.sctp ↗.strictCwndBooking	bool	false
upf.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
upf.sctp ↗.cmtCCPathGroups	string	“”
upf.sctp ↗.rpPathBlocking	bool	false
upf.sctp ↗.rpScaleBlockingTimeout	bool	false
upf.sctp ↗.rpMinCwnd	int	1
upf.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.quic ↗.routingTableModule	string		Set by StandardHost.
upf.quic ↗.sendZeroRttTokenAsServer	bool	false
upf.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
upf.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
upf.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
upf.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
upf.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
upf.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
upf.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
upf.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
upf.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
upf.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
upf.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
upf.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
upf.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
upf.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
upf.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
upf.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
upf.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
upf.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
upf.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
upf.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
upf.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
upf.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
upf.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
upf.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
upf.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
upf.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
upf.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
upf.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
upf.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
upf.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.tn ↗.forwardServiceRegistration	bool	true
upf.tn ↗.forwardProtocolRegistration	bool	true
upf.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.at ↗.forwardServiceRegistration	bool	true
upf.at ↗.forwardProtocolRegistration	bool	true
upf.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.dnPpp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnPpp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.dnPpp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.dnPpp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.dnPpp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.dnPpp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.dnPpp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.dnPpp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.dnPpp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.dnPpp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.dnPpp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.dnPpp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.dnPpp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnPpp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.dnPpp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.dnPpp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnPpp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
upf.dnPpp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
upf.dnPpp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
upf.dnPpp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
upf.dnPpp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
upf.dnPpp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnPpp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
upf.dnPpp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
upf.dnPpp ↗.ppp ↗.mtu	int	4470B
upf.dnPpp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
upf.dnPpp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
upf.relay.trafficFlowFilter.binderModule	string	“binder”
upf.relay.trafficFlowFilter.fastForwarding	bool	true
upf.relay.gtpUser.binderModule	string	“binder”
upf.relay.gtpUser.localPort	int	31
upf.relay.gtpUser.tunnelPeerPort	int	31
upf.rd ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.rd ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.rd ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.nodeControl.binderModule	string	“binder”
upf.nodeControl.gtpUserModule	string	“^.relay.gtpUser”
upf.nodeControl.trafficFlowFilterModule	string	“^.relay.trafficFlowFilter”
upf.nodeControl.ethernetBridgeModule	string	“^.ethBridge.sessionMux”	The node’s Ethernet session bridge (see EthernetSessionBridge), if it has one
upf.nodeControl.unstructuredPrefix	string	“”	The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. “2001:db8:5::/64” or “10.5.0.0/16”; empty = the node anchors no Unstructured session (see the main comment)
upf.nodeControl.unstructuredServer	string	“”	The application server the Unstructured sessions’ uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix
upf.nodeControl.unstructuredServerPort	int	-1	The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions
upf.nodeControl.unstructuredPort	int	-1	The UDP port the node receives the Unstructured sessions’ downlink on, and sends their uplink from; must be set for Unstructured sessions
upf.ndResponder.binderModule	string	“binder”
upf.ndResponder.linkLocalAddress	string	“fe80::1”	The router’s address on every session’s link
upf.ndResponder.routerLifetime	double	9000s	Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)
upf.ndResponder.curHopLimit	int	64	Cur Hop Limit in the Router Advertisements (0 = unspecified)
upf.ndResponder.checksumMode	string	“declared”
upf.ethBridge.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.macTable ↗.agingTime	double	120s
upf.ethBridge.macTable ↗.forwardingTable	object	[]
upf.ethBridge.macTable ↗.forwardingTableFile	string	“”
upf.ethBridge.macTable ↗.interfaceTableModule	string
upf.ethBridge.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
upf.ethBridge.sessionMux.interfaceTableModule	string		The bridge’s interface table, which the session ports are registered in
upf.ethBridge.sessionMux.macTableModule	string		The bridge’s MAC table, flushed of a released session’s port
upf.ethBridge.sessionMux.portModuleType	string	“simu5g.corenetwork.ethernetSessionBridge.EthernetSessionPort”	The module type of the session ports
upf.ethBridge.sessionMux.portDisplayString	string	“p=500,420,row,100;g=sessionPorts”	Display string of the session ports (their place in the bridge’s layout)
upf.ethBridge.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ethBridge.cb ↗.forwardServiceRegistration	bool	true
upf.ethBridge.cb ↗.forwardProtocolRegistration	bool	true
upf.ethBridge.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ethBridge.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ethBridge.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.forwardProtocolRegistration	bool	true
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ethBridge.bridging ↗.directionReverser ↗.fork ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardVlan	bool	true
upf.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardPcp	bool	true
upf.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.excludeEncapsulationProtocols	object	[]
upf.ethBridge.bridging ↗.directionReverser ↗.join ↗.displayStringTextFormat	string	“passed %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bridging ↗.directionReverser ↗.join ↗.forwardServiceRegistration	bool	true
upf.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.macTableModule	string		Relative module path of MAC table
upf.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.interfaceTableModule	string		Relative module path of the interface table
upf.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.macTableModule	string		Relative module path of MAC table
upf.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.interfaceTableModule	string		Relative module path of interface table
upf.ethBridge.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ethBridge.bl ↗.forwardServiceRegistration	bool	true
upf.ethBridge.bl ↗.forwardProtocolRegistration	bool	true
upf.ethBridge.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ethBridge.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ethBridge.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.ethBridge.ethernet ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.socketCommandProcessor ↗.socketTableModule	string
upf.ethBridge.ethernet ↗.macHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.macHeaderInserter ↗.interfaceTableModule	string
upf.ethBridge.ethernet ↗.paddingInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.paddingInserter ↗.minLength	int
upf.ethBridge.ethernet ↗.paddingInserter ↗.roundingLength	int	1B
upf.ethBridge.ethernet ↗.paddingInserter ↗.insertionPosition	string	“back”
upf.ethBridge.ethernet ↗.fcsInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.fcsInserter ↗.fcsMode	string	“declared”
upf.ethBridge.ethernet ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.socketPacketProcessor ↗.socketTableModule	string
upf.ethBridge.ethernet ↗.macHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.macHeaderChecker ↗.backpressure	bool	false
upf.ethBridge.ethernet ↗.macHeaderChecker ↗.interfaceTableModule	string
upf.ethBridge.ethernet ↗.macHeaderChecker ↗.promiscuous	bool	false
upf.ethBridge.ethernet ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ethernet ↗.fcsChecker ↗.backpressure	bool	false
upf.ethBridge.ethernet ↗.fcsChecker ↗.popFcs	bool	true
upf.ethBridge.ieee8021q ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.socketTableModule	string
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.vlanTagType	string	“c”
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.nextProtocol	string	“ethernetmac”
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultVlanId	int	-1
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultPcp	int	-1
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultUserPriority	int	-1
upf.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultDropEligible	int	-1	<0: unspecified, 0: false, >0: true
upf.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.socketTableModule	string
upf.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.backpressure	bool	false
upf.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanTagType	string	“c”
upf.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanIdFilter	object	[]
upf.ethBridge.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.ethBridge.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
upf.ethBridge.li ↗.forwardServiceRegistration	bool	true
upf.ethBridge.li ↗.forwardProtocolRegistration	bool	true
upf.ethBridge.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
upf.ethBridge.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
upf.ethBridge.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
upf.dnEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
upf.dnEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
upf.dnEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
upf.dnEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
upf.dnEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
upf.dnEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
upf.dnEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
upf.dnEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
upf.dnEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
upf.dnEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
upf.dnEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
upf.dnEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
upf.dnEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
upf.dnEth ↗.macLayer ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.macLayer ↗.queue ↗.packetCapacity	int	-1	Maximum number of packets in the queue, no limit by default
upf.dnEth ↗.macLayer ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
upf.dnEth ↗.macLayer ↗.queue ↗.dropperClass	string	“”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
upf.dnEth ↗.macLayer ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
upf.dnEth ↗.macLayer ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
upf.dnEth ↗.macLayer ↗.server ↗.displayStringTextFormat	string	“served %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.macLayer ↗.server ↗.serveSchedulingPriority	int	0	Specifies the FES scheduling priority for the extra event that is pulling the packet, -1 means no extra event
upf.dnEth ↗.macLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.macLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnEth ↗.macLayer ↗.outboundEmitter ↗.direction	string	“undefined”
upf.dnEth ↗.macLayer ↗.outboundEmitter ↗.signalName	string
upf.dnEth ↗.macLayer ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.macLayer ↗.fcsChecker ↗.backpressure	bool	false
upf.dnEth ↗.macLayer ↗.fcsChecker ↗.popFcs	bool	false
upf.dnEth ↗.macLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.macLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnEth ↗.macLayer ↗.inboundEmitter ↗.direction	string	“undefined”
upf.dnEth ↗.macLayer ↗.inboundEmitter ↗.signalName	string
upf.dnEth ↗.phyLayer ↗.phyHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.displayStringTextFormat	string	“delayed %p pk (%l)\nifg: %g”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
upf.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.initialChannelBusy	bool	false	Assume that the channel was busy before the simulation started
upf.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.duration	double	96s / dropUnit(parent.bitrate)
upf.dnEth ↗.phyLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnEth ↗.phyLayer ↗.outboundEmitter ↗.direction	string	“undefined”
upf.dnEth ↗.phyLayer ↗.outboundEmitter ↗.signalName	string
upf.dnEth ↗.phyLayer ↗.transmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.transmitter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
upf.dnEth ↗.phyLayer ↗.transmitter ↗.datarate	double	parent.bitrate
upf.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.backpressure	bool	false
upf.dnEth ↗.phyLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
upf.dnEth ↗.phyLayer ↗.inboundEmitter ↗.direction	string	“undefined”
upf.dnEth ↗.phyLayer ↗.inboundEmitter ↗.signalName	string
upf.dnEth ↗.phyLayer ↗.receiver ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
upf.dnEth ↗.phyLayer ↗.receiver ↗.datarate	double	parent.bitrate
iUpf1.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.status ↗.initialStatus	string	“UP”	Initial status of the network node
iUpf1.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.environment ↗.initStage	int	0	Initialization stage for the setup command
iUpf1.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
iUpf1.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
iUpf1.environment ↗.setupCommand	string	“”	A host OS system command
iUpf1.environment ↗.teardownCommand	string	“”	A host OS system command
iUpf1.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
iUpf1.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
iUpf1.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.cb ↗.forwardServiceRegistration	bool	true
iUpf1.cb ↗.forwardProtocolRegistration	bool	true
iUpf1.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.bl ↗.forwardServiceRegistration	bool	true
iUpf1.bl ↗.forwardProtocolRegistration	bool	true
iUpf1.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
iUpf1.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ethernet ↗.fcsMode	string	“declared”
iUpf1.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
iUpf1.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
iUpf1.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.li ↗.forwardServiceRegistration	bool	true
iUpf1.li ↗.forwardProtocolRegistration	bool	true
iUpf1.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.lo ↗.lo ↗.mtu	int	4470B
iUpf1.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.wlan ↗.agent ↗.mibModule	string
iUpf1.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
iUpf1.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
iUpf1.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
iUpf1.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
iUpf1.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
iUpf1.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
iUpf1.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
iUpf1.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
iUpf1.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
iUpf1.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
iUpf1.wlan ↗.mgmt ↗.mibModule	string
iUpf1.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
iUpf1.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
iUpf1.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
iUpf1.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
iUpf1.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
iUpf1.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
iUpf1.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
iUpf1.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
iUpf1.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
iUpf1.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
iUpf1.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
iUpf1.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
iUpf1.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
iUpf1.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
iUpf1.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
iUpf1.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
iUpf1.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.ds ↗.mibModule	string
iUpf1.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.wlan ↗.mac ↗.tx ↗.rxModule	string
iUpf1.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
iUpf1.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf1.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf1.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf1.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf1.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
iUpf1.ppp ↗.ppp ↗.mtu	int	4470B
iUpf1.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
iUpf1.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf1.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.tun ↗.tun ↗.mtu	int	1500B
iUpf1.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.virt ↗.tunnel ↗.interfaceTableModule	string
iUpf1.virt ↗.tunnel ↗.realInterface	string
iUpf1.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
iUpf1.virt ↗.tunnel ↗.address	string	“copy”
iUpf1.virt ↗.tunnel ↗.vlanId	int	-1
iUpf1.virt ↗.tunnel ↗.steal	bool	vlanId != -1
iUpf1.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.configurator ↗.routingTableModule	string
iUpf1.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
iUpf1.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
iUpf1.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
iUpf1.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
iUpf1.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
iUpf1.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
iUpf1.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
iUpf1.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
iUpf1.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
iUpf1.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
iUpf1.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
iUpf1.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
iUpf1.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.igmp ↗.routingTableModule	string
iUpf1.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
iUpf1.ipv4 ↗.igmp ↗.enabled	bool	true
iUpf1.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
iUpf1.ipv4 ↗.igmp ↗.queryInterval	double	125s
iUpf1.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
iUpf1.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
iUpf1.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
iUpf1.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
iUpf1.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
iUpf1.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
iUpf1.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
iUpf1.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
iUpf1.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.icmp ↗.routingTableModule	string
iUpf1.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
iUpf1.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
iUpf1.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
iUpf1.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
iUpf1.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.ip ↗.routingTableModule	string
iUpf1.ipv4 ↗.ip ↗.arpModule	string
iUpf1.ipv4 ↗.ip ↗.icmpModule	string
iUpf1.ipv4 ↗.ip ↗.checksumMode	string	“declared”
iUpf1.ipv4 ↗.ip ↗.timeToLive	int	32
iUpf1.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
iUpf1.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
iUpf1.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
iUpf1.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
iUpf1.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
iUpf1.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
iUpf1.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
iUpf1.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv4 ↗.arp ↗.routingTableModule	string
iUpf1.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
iUpf1.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
iUpf1.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
iUpf1.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
iUpf1.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
iUpf1.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
iUpf1.ipv4 ↗.ipsec ↗.interfaceTableModule	string
iUpf1.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
iUpf1.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
iUpf1.ipv4 ↗.ipsec ↗.spdConfig	xml
iUpf1.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
iUpf1.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
iUpf1.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
iUpf1.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
iUpf1.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
iUpf1.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
iUpf1.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
iUpf1.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
iUpf1.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
iUpf1.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
iUpf1.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
iUpf1.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.configurator ↗.interfaceTableModule	string
iUpf1.ipv6 ↗.configurator ↗.routingTableModule	string
iUpf1.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
iUpf1.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
iUpf1.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
iUpf1.ipv6 ↗.routingTable ↗.forwarding	bool	false
iUpf1.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
iUpf1.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
iUpf1.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
iUpf1.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
iUpf1.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
iUpf1.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
iUpf1.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
iUpf1.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
iUpf1.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
iUpf1.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
iUpf1.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
iUpf1.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
iUpf1.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
iUpf1.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
iUpf1.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
iUpf1.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
iUpf1.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
iUpf1.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
iUpf1.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
iUpf1.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
iUpf1.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
iUpf1.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
iUpf1.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
iUpf1.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
iUpf1.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
iUpf1.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
iUpf1.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
iUpf1.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
iUpf1.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv6 ↗.ipv6 ↗.routingTableModule	string
iUpf1.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
iUpf1.ipv6 ↗.ipv6 ↗.icmpv6Module	string
iUpf1.ipv6 ↗.ipv6 ↗.procDelay	double	0s
iUpf1.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
iUpf1.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.ipsec ↗.interfaceTableModule	string
iUpf1.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
iUpf1.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
iUpf1.ipv6 ↗.ipsec ↗.spdConfig	xml
iUpf1.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
iUpf1.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
iUpf1.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
iUpf1.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
iUpf1.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
iUpf1.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
iUpf1.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
iUpf1.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
iUpf1.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
iUpf1.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
iUpf1.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
iUpf1.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
iUpf1.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
iUpf1.ipv6 ↗.mipv6 ↗.isMobileNode	bool
iUpf1.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
iUpf1.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
iUpf1.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
iUpf1.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
iUpf1.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
iUpf1.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
iUpf1.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
iUpf1.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
iUpf1.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
iUpf1.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
iUpf1.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
iUpf1.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
iUpf1.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
iUpf1.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
iUpf1.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
iUpf1.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
iUpf1.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
iUpf1.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
iUpf1.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
iUpf1.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
iUpf1.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
iUpf1.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
iUpf1.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
iUpf1.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
iUpf1.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
iUpf1.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.nl ↗.forwardServiceRegistration	bool	true
iUpf1.nl ↗.forwardProtocolRegistration	bool	true
iUpf1.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.udp ↗.checksumMode	string	“declared”
iUpf1.udp ↗.defaultMulticastLoop	bool	true
iUpf1.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.tcp ↗.checksumMode	string	“declared”
iUpf1.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
iUpf1.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
iUpf1.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
iUpf1.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
iUpf1.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
iUpf1.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
iUpf1.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
iUpf1.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
iUpf1.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
iUpf1.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
iUpf1.tcp ↗.msl	int	120s	Maximum Segment Lifetime
iUpf1.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
iUpf1.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
iUpf1.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
iUpf1.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
iUpf1.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf1.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
iUpf1.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
iUpf1.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
iUpf1.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
iUpf1.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.sctp ↗.interfaceTableModule	string
iUpf1.sctp ↗.routingTableModule	string
iUpf1.sctp ↗.checksumMode	string	“declared”
iUpf1.sctp ↗.numGapReports	int	3
iUpf1.sctp ↗.rtoInitial	double	3s
iUpf1.sctp ↗.rtoMin	double	1s
iUpf1.sctp ↗.rtoMax	double	60s
iUpf1.sctp ↗.rtoAlpha	double	0.125
iUpf1.sctp ↗.rtoBeta	double	0.250
iUpf1.sctp ↗.maxBurst	int	4
iUpf1.sctp ↗.maxBurstVariant	string	“maxBurst”
iUpf1.sctp ↗.initialWindow	int	0
iUpf1.sctp ↗.assocMaxRetrans	int	10
iUpf1.sctp ↗.pathMaxRetrans	int	5
iUpf1.sctp ↗.maxInitRetrans	int	8
iUpf1.sctp ↗.sackPeriod	double	200ms
iUpf1.sctp ↗.sackFrequency	int	2
iUpf1.sctp ↗.reactivatePrimaryPath	bool	false
iUpf1.sctp ↗.sendQueueLimit	int	0
iUpf1.sctp ↗.validCookieLifetime	double	10s
iUpf1.sctp ↗.enableHeartbeats	bool	true
iUpf1.sctp ↗.hbInterval	double	30s
iUpf1.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
iUpf1.sctp ↗.nagleEnabled	bool	true
iUpf1.sctp ↗.naglePoint	int	1468
iUpf1.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
iUpf1.sctp ↗.fastRecoverySupported	bool	true
iUpf1.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
iUpf1.sctp ↗.ccModule	int	0	RFC4960=0
iUpf1.sctp ↗.osbWithHeader	bool	false
iUpf1.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
iUpf1.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
iUpf1.sctp ↗.arwnd	int	65535
iUpf1.sctp ↗.swsLimit	int	3000	Limit for SWS
iUpf1.sctp ↗.udpEncapsEnabled	bool	false
iUpf1.sctp ↗.natFriendly	bool	false
iUpf1.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
iUpf1.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
iUpf1.sctp ↗.tellArwnd	bool	false	For flow control
iUpf1.sctp ↗.messageAcceptLimit	int	0	For flow control
iUpf1.sctp ↗.fairStart	double	0s
iUpf1.sctp ↗.fairStop	double	0s
iUpf1.sctp ↗.streamsToPaths	string	“”
iUpf1.sctp ↗.startEndToEndDelay	int	0
iUpf1.sctp ↗.stopEndToEndDelay	int	10
iUpf1.sctp ↗.throughputInterval	double	1
iUpf1.sctp ↗.auth	bool	false
iUpf1.sctp ↗.chunks	string	“”
iUpf1.sctp ↗.padding	bool	false
iUpf1.sctp ↗.addIP	bool	false
iUpf1.sctp ↗.addTime	double	0s
iUpf1.sctp ↗.addAddress	string	“”
iUpf1.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
iUpf1.sctp ↗.packetDrop	bool	false
iUpf1.sctp ↗.sackNow	bool	false
iUpf1.sctp ↗.highSpeedCC	bool	false
iUpf1.sctp ↗.checkSackSeqNumber	bool	false
iUpf1.sctp ↗.nrSack	bool	false
iUpf1.sctp ↗.disableReneging	bool	false
iUpf1.sctp ↗.gapReportLimit	int	100000000
iUpf1.sctp ↗.gapListOptimizationVariant	string	“none”
iUpf1.sctp ↗.smartOverfullSACKHandling	bool	false
iUpf1.sctp ↗.allowQoSTracking	bool	false
iUpf1.sctp ↗.qosTrackingInterval	double	1.0s
iUpf1.sctp ↗.cmtSendAllVariant	string	“normal”
iUpf1.sctp ↗.cmtRetransmissionVariant	string	“normal”
iUpf1.sctp ↗.cmtCUCVariant	string	“normal”
iUpf1.sctp ↗.cmtBufferSplitVariant	string	“none”
iUpf1.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
iUpf1.sctp ↗.cmtUseSFR	bool	true
iUpf1.sctp ↗.cmtUseDAC	bool	true
iUpf1.sctp ↗.cmtUseFRC	bool	true
iUpf1.sctp ↗.cmtSmartT3Reset	bool	true
iUpf1.sctp ↗.cmtSmartFastRTX	bool	true
iUpf1.sctp ↗.cmtSmartReneging	bool	false
iUpf1.sctp ↗.cmtSlowPathRTTUpdate	bool	false
iUpf1.sctp ↗.cmtChunkReschedulingVariant	string	“none”
iUpf1.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
iUpf1.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
iUpf1.sctp ↗.movedChunkFastRTXFactor	double	2.0
iUpf1.sctp ↗.cmtSackPath	string	“standard”
iUpf1.sctp ↗.strictCwndBooking	bool	false
iUpf1.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
iUpf1.sctp ↗.cmtCCPathGroups	string	“”
iUpf1.sctp ↗.rpPathBlocking	bool	false
iUpf1.sctp ↗.rpScaleBlockingTimeout	bool	false
iUpf1.sctp ↗.rpMinCwnd	int	1
iUpf1.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.quic ↗.routingTableModule	string		Set by StandardHost.
iUpf1.quic ↗.sendZeroRttTokenAsServer	bool	false
iUpf1.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
iUpf1.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
iUpf1.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
iUpf1.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
iUpf1.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
iUpf1.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
iUpf1.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
iUpf1.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
iUpf1.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
iUpf1.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
iUpf1.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
iUpf1.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
iUpf1.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
iUpf1.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
iUpf1.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
iUpf1.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
iUpf1.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
iUpf1.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
iUpf1.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
iUpf1.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
iUpf1.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
iUpf1.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
iUpf1.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
iUpf1.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
iUpf1.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
iUpf1.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
iUpf1.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
iUpf1.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
iUpf1.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
iUpf1.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.tn ↗.forwardServiceRegistration	bool	true
iUpf1.tn ↗.forwardProtocolRegistration	bool	true
iUpf1.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.at ↗.forwardServiceRegistration	bool	true
iUpf1.at ↗.forwardProtocolRegistration	bool	true
iUpf1.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.dnPpp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnPpp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.dnPpp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.dnPpp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.dnPpp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.dnPpp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.dnPpp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.dnPpp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.dnPpp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.dnPpp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.dnPpp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.dnPpp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.dnPpp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnPpp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.dnPpp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.dnPpp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnPpp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
iUpf1.dnPpp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf1.dnPpp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf1.dnPpp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf1.dnPpp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf1.dnPpp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnPpp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf1.dnPpp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
iUpf1.dnPpp ↗.ppp ↗.mtu	int	4470B
iUpf1.dnPpp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
iUpf1.dnPpp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf1.relay.trafficFlowFilter.binderModule	string	“binder”
iUpf1.relay.trafficFlowFilter.fastForwarding	bool	true
iUpf1.relay.gtpUser.binderModule	string	“binder”
iUpf1.relay.gtpUser.localPort	int	31
iUpf1.relay.gtpUser.tunnelPeerPort	int	31
iUpf1.rd ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.rd ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.rd ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.nodeControl.binderModule	string	“binder”
iUpf1.nodeControl.gtpUserModule	string	“^.relay.gtpUser”
iUpf1.nodeControl.trafficFlowFilterModule	string	“^.relay.trafficFlowFilter”
iUpf1.nodeControl.ethernetBridgeModule	string	“^.ethBridge.sessionMux”	The node’s Ethernet session bridge (see EthernetSessionBridge), if it has one
iUpf1.nodeControl.unstructuredPrefix	string	“”	The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. “2001:db8:5::/64” or “10.5.0.0/16”; empty = the node anchors no Unstructured session (see the main comment)
iUpf1.nodeControl.unstructuredServer	string	“”	The application server the Unstructured sessions’ uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix
iUpf1.nodeControl.unstructuredServerPort	int	-1	The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions
iUpf1.nodeControl.unstructuredPort	int	-1	The UDP port the node receives the Unstructured sessions’ downlink on, and sends their uplink from; must be set for Unstructured sessions
iUpf1.ndResponder.binderModule	string	“binder”
iUpf1.ndResponder.linkLocalAddress	string	“fe80::1”	The router’s address on every session’s link
iUpf1.ndResponder.routerLifetime	double	9000s	Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)
iUpf1.ndResponder.curHopLimit	int	64	Cur Hop Limit in the Router Advertisements (0 = unspecified)
iUpf1.ndResponder.checksumMode	string	“declared”
iUpf1.ethBridge.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.macTable ↗.agingTime	double	120s
iUpf1.ethBridge.macTable ↗.forwardingTable	object	[]
iUpf1.ethBridge.macTable ↗.forwardingTableFile	string	“”
iUpf1.ethBridge.macTable ↗.interfaceTableModule	string
iUpf1.ethBridge.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
iUpf1.ethBridge.sessionMux.interfaceTableModule	string		The bridge’s interface table, which the session ports are registered in
iUpf1.ethBridge.sessionMux.macTableModule	string		The bridge’s MAC table, flushed of a released session’s port
iUpf1.ethBridge.sessionMux.portModuleType	string	“simu5g.corenetwork.ethernetSessionBridge.EthernetSessionPort”	The module type of the session ports
iUpf1.ethBridge.sessionMux.portDisplayString	string	“p=500,420,row,100;g=sessionPorts”	Display string of the session ports (their place in the bridge’s layout)
iUpf1.ethBridge.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ethBridge.cb ↗.forwardServiceRegistration	bool	true
iUpf1.ethBridge.cb ↗.forwardProtocolRegistration	bool	true
iUpf1.ethBridge.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ethBridge.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ethBridge.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.forwardProtocolRegistration	bool	true
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ethBridge.bridging ↗.directionReverser ↗.fork ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardVlan	bool	true
iUpf1.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardPcp	bool	true
iUpf1.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.excludeEncapsulationProtocols	object	[]
iUpf1.ethBridge.bridging ↗.directionReverser ↗.join ↗.displayStringTextFormat	string	“passed %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bridging ↗.directionReverser ↗.join ↗.forwardServiceRegistration	bool	true
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.macTableModule	string		Relative module path of MAC table
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.interfaceTableModule	string		Relative module path of the interface table
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.macTableModule	string		Relative module path of MAC table
iUpf1.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.interfaceTableModule	string		Relative module path of interface table
iUpf1.ethBridge.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ethBridge.bl ↗.forwardServiceRegistration	bool	true
iUpf1.ethBridge.bl ↗.forwardProtocolRegistration	bool	true
iUpf1.ethBridge.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ethBridge.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ethBridge.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.ethBridge.ethernet ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.socketCommandProcessor ↗.socketTableModule	string
iUpf1.ethBridge.ethernet ↗.macHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.macHeaderInserter ↗.interfaceTableModule	string
iUpf1.ethBridge.ethernet ↗.paddingInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.paddingInserter ↗.minLength	int
iUpf1.ethBridge.ethernet ↗.paddingInserter ↗.roundingLength	int	1B
iUpf1.ethBridge.ethernet ↗.paddingInserter ↗.insertionPosition	string	“back”
iUpf1.ethBridge.ethernet ↗.fcsInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.fcsInserter ↗.fcsMode	string	“declared”
iUpf1.ethBridge.ethernet ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.socketPacketProcessor ↗.socketTableModule	string
iUpf1.ethBridge.ethernet ↗.macHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.macHeaderChecker ↗.backpressure	bool	false
iUpf1.ethBridge.ethernet ↗.macHeaderChecker ↗.interfaceTableModule	string
iUpf1.ethBridge.ethernet ↗.macHeaderChecker ↗.promiscuous	bool	false
iUpf1.ethBridge.ethernet ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ethernet ↗.fcsChecker ↗.backpressure	bool	false
iUpf1.ethBridge.ethernet ↗.fcsChecker ↗.popFcs	bool	true
iUpf1.ethBridge.ieee8021q ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.socketTableModule	string
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.vlanTagType	string	“c”
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.nextProtocol	string	“ethernetmac”
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultVlanId	int	-1
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultPcp	int	-1
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultUserPriority	int	-1
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultDropEligible	int	-1	<0: unspecified, 0: false, >0: true
iUpf1.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.socketTableModule	string
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.backpressure	bool	false
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanTagType	string	“c”
iUpf1.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanIdFilter	object	[]
iUpf1.ethBridge.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.ethBridge.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf1.ethBridge.li ↗.forwardServiceRegistration	bool	true
iUpf1.ethBridge.li ↗.forwardProtocolRegistration	bool	true
iUpf1.ethBridge.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf1.ethBridge.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf1.ethBridge.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf1.dnEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf1.dnEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf1.dnEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf1.dnEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf1.dnEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf1.dnEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf1.dnEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf1.dnEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf1.dnEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf1.dnEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf1.dnEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf1.dnEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf1.dnEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf1.dnEth ↗.macLayer ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.macLayer ↗.queue ↗.packetCapacity	int	-1	Maximum number of packets in the queue, no limit by default
iUpf1.dnEth ↗.macLayer ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf1.dnEth ↗.macLayer ↗.queue ↗.dropperClass	string	“”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf1.dnEth ↗.macLayer ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf1.dnEth ↗.macLayer ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf1.dnEth ↗.macLayer ↗.server ↗.displayStringTextFormat	string	“served %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.macLayer ↗.server ↗.serveSchedulingPriority	int	0	Specifies the FES scheduling priority for the extra event that is pulling the packet, -1 means no extra event
iUpf1.dnEth ↗.macLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.macLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnEth ↗.macLayer ↗.outboundEmitter ↗.direction	string	“undefined”
iUpf1.dnEth ↗.macLayer ↗.outboundEmitter ↗.signalName	string
iUpf1.dnEth ↗.macLayer ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.macLayer ↗.fcsChecker ↗.backpressure	bool	false
iUpf1.dnEth ↗.macLayer ↗.fcsChecker ↗.popFcs	bool	false
iUpf1.dnEth ↗.macLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.macLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnEth ↗.macLayer ↗.inboundEmitter ↗.direction	string	“undefined”
iUpf1.dnEth ↗.macLayer ↗.inboundEmitter ↗.signalName	string
iUpf1.dnEth ↗.phyLayer ↗.phyHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.displayStringTextFormat	string	“delayed %p pk (%l)\nifg: %g”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
iUpf1.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.initialChannelBusy	bool	false	Assume that the channel was busy before the simulation started
iUpf1.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.duration	double	96s / dropUnit(parent.bitrate)
iUpf1.dnEth ↗.phyLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnEth ↗.phyLayer ↗.outboundEmitter ↗.direction	string	“undefined”
iUpf1.dnEth ↗.phyLayer ↗.outboundEmitter ↗.signalName	string
iUpf1.dnEth ↗.phyLayer ↗.transmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.transmitter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
iUpf1.dnEth ↗.phyLayer ↗.transmitter ↗.datarate	double	parent.bitrate
iUpf1.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.backpressure	bool	false
iUpf1.dnEth ↗.phyLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf1.dnEth ↗.phyLayer ↗.inboundEmitter ↗.direction	string	“undefined”
iUpf1.dnEth ↗.phyLayer ↗.inboundEmitter ↗.signalName	string
iUpf1.dnEth ↗.phyLayer ↗.receiver ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf1.dnEth ↗.phyLayer ↗.receiver ↗.datarate	double	parent.bitrate
iUpf2.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.status ↗.initialStatus	string	“UP”	Initial status of the network node
iUpf2.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.environment ↗.initStage	int	0	Initialization stage for the setup command
iUpf2.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
iUpf2.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
iUpf2.environment ↗.setupCommand	string	“”	A host OS system command
iUpf2.environment ↗.teardownCommand	string	“”	A host OS system command
iUpf2.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
iUpf2.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
iUpf2.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.cb ↗.forwardServiceRegistration	bool	true
iUpf2.cb ↗.forwardProtocolRegistration	bool	true
iUpf2.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.bl ↗.forwardServiceRegistration	bool	true
iUpf2.bl ↗.forwardProtocolRegistration	bool	true
iUpf2.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
iUpf2.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ethernet ↗.fcsMode	string	“declared”
iUpf2.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
iUpf2.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
iUpf2.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.li ↗.forwardServiceRegistration	bool	true
iUpf2.li ↗.forwardProtocolRegistration	bool	true
iUpf2.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.lo ↗.lo ↗.mtu	int	4470B
iUpf2.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.wlan ↗.agent ↗.mibModule	string
iUpf2.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
iUpf2.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
iUpf2.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
iUpf2.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
iUpf2.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
iUpf2.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
iUpf2.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
iUpf2.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
iUpf2.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
iUpf2.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
iUpf2.wlan ↗.mgmt ↗.mibModule	string
iUpf2.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
iUpf2.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
iUpf2.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
iUpf2.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
iUpf2.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
iUpf2.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
iUpf2.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
iUpf2.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
iUpf2.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
iUpf2.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
iUpf2.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
iUpf2.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
iUpf2.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
iUpf2.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
iUpf2.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
iUpf2.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
iUpf2.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.ds ↗.mibModule	string
iUpf2.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.wlan ↗.mac ↗.tx ↗.rxModule	string
iUpf2.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
iUpf2.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf2.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf2.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf2.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf2.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
iUpf2.ppp ↗.ppp ↗.mtu	int	4470B
iUpf2.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
iUpf2.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf2.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.tun ↗.tun ↗.mtu	int	1500B
iUpf2.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.virt ↗.tunnel ↗.interfaceTableModule	string
iUpf2.virt ↗.tunnel ↗.realInterface	string
iUpf2.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
iUpf2.virt ↗.tunnel ↗.address	string	“copy”
iUpf2.virt ↗.tunnel ↗.vlanId	int	-1
iUpf2.virt ↗.tunnel ↗.steal	bool	vlanId != -1
iUpf2.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.configurator ↗.routingTableModule	string
iUpf2.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
iUpf2.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
iUpf2.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
iUpf2.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
iUpf2.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
iUpf2.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
iUpf2.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
iUpf2.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
iUpf2.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
iUpf2.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
iUpf2.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
iUpf2.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
iUpf2.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.igmp ↗.routingTableModule	string
iUpf2.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
iUpf2.ipv4 ↗.igmp ↗.enabled	bool	true
iUpf2.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
iUpf2.ipv4 ↗.igmp ↗.queryInterval	double	125s
iUpf2.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
iUpf2.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
iUpf2.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
iUpf2.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
iUpf2.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
iUpf2.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
iUpf2.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
iUpf2.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
iUpf2.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.icmp ↗.routingTableModule	string
iUpf2.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
iUpf2.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
iUpf2.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
iUpf2.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
iUpf2.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.ip ↗.routingTableModule	string
iUpf2.ipv4 ↗.ip ↗.arpModule	string
iUpf2.ipv4 ↗.ip ↗.icmpModule	string
iUpf2.ipv4 ↗.ip ↗.checksumMode	string	“declared”
iUpf2.ipv4 ↗.ip ↗.timeToLive	int	32
iUpf2.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
iUpf2.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
iUpf2.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
iUpf2.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
iUpf2.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
iUpf2.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
iUpf2.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
iUpf2.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv4 ↗.arp ↗.routingTableModule	string
iUpf2.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
iUpf2.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
iUpf2.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
iUpf2.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
iUpf2.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
iUpf2.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
iUpf2.ipv4 ↗.ipsec ↗.interfaceTableModule	string
iUpf2.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
iUpf2.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
iUpf2.ipv4 ↗.ipsec ↗.spdConfig	xml
iUpf2.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
iUpf2.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
iUpf2.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
iUpf2.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
iUpf2.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
iUpf2.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
iUpf2.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
iUpf2.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
iUpf2.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
iUpf2.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
iUpf2.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
iUpf2.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.configurator ↗.interfaceTableModule	string
iUpf2.ipv6 ↗.configurator ↗.routingTableModule	string
iUpf2.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
iUpf2.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
iUpf2.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
iUpf2.ipv6 ↗.routingTable ↗.forwarding	bool	false
iUpf2.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
iUpf2.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
iUpf2.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
iUpf2.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
iUpf2.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
iUpf2.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
iUpf2.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
iUpf2.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
iUpf2.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
iUpf2.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
iUpf2.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
iUpf2.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
iUpf2.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
iUpf2.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
iUpf2.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
iUpf2.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
iUpf2.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
iUpf2.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
iUpf2.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
iUpf2.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
iUpf2.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
iUpf2.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
iUpf2.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
iUpf2.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
iUpf2.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
iUpf2.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
iUpf2.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
iUpf2.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
iUpf2.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv6 ↗.ipv6 ↗.routingTableModule	string
iUpf2.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
iUpf2.ipv6 ↗.ipv6 ↗.icmpv6Module	string
iUpf2.ipv6 ↗.ipv6 ↗.procDelay	double	0s
iUpf2.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
iUpf2.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.ipsec ↗.interfaceTableModule	string
iUpf2.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
iUpf2.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
iUpf2.ipv6 ↗.ipsec ↗.spdConfig	xml
iUpf2.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
iUpf2.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
iUpf2.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
iUpf2.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
iUpf2.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
iUpf2.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
iUpf2.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
iUpf2.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
iUpf2.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
iUpf2.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
iUpf2.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
iUpf2.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
iUpf2.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
iUpf2.ipv6 ↗.mipv6 ↗.isMobileNode	bool
iUpf2.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
iUpf2.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
iUpf2.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
iUpf2.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
iUpf2.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
iUpf2.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
iUpf2.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
iUpf2.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
iUpf2.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
iUpf2.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
iUpf2.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
iUpf2.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
iUpf2.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
iUpf2.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
iUpf2.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
iUpf2.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
iUpf2.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
iUpf2.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
iUpf2.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
iUpf2.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
iUpf2.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
iUpf2.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
iUpf2.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
iUpf2.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
iUpf2.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
iUpf2.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.nl ↗.forwardServiceRegistration	bool	true
iUpf2.nl ↗.forwardProtocolRegistration	bool	true
iUpf2.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.udp ↗.checksumMode	string	“declared”
iUpf2.udp ↗.defaultMulticastLoop	bool	true
iUpf2.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.tcp ↗.checksumMode	string	“declared”
iUpf2.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
iUpf2.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
iUpf2.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
iUpf2.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
iUpf2.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
iUpf2.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
iUpf2.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
iUpf2.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
iUpf2.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
iUpf2.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
iUpf2.tcp ↗.msl	int	120s	Maximum Segment Lifetime
iUpf2.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
iUpf2.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
iUpf2.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
iUpf2.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
iUpf2.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf2.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
iUpf2.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
iUpf2.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
iUpf2.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
iUpf2.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.sctp ↗.interfaceTableModule	string
iUpf2.sctp ↗.routingTableModule	string
iUpf2.sctp ↗.checksumMode	string	“declared”
iUpf2.sctp ↗.numGapReports	int	3
iUpf2.sctp ↗.rtoInitial	double	3s
iUpf2.sctp ↗.rtoMin	double	1s
iUpf2.sctp ↗.rtoMax	double	60s
iUpf2.sctp ↗.rtoAlpha	double	0.125
iUpf2.sctp ↗.rtoBeta	double	0.250
iUpf2.sctp ↗.maxBurst	int	4
iUpf2.sctp ↗.maxBurstVariant	string	“maxBurst”
iUpf2.sctp ↗.initialWindow	int	0
iUpf2.sctp ↗.assocMaxRetrans	int	10
iUpf2.sctp ↗.pathMaxRetrans	int	5
iUpf2.sctp ↗.maxInitRetrans	int	8
iUpf2.sctp ↗.sackPeriod	double	200ms
iUpf2.sctp ↗.sackFrequency	int	2
iUpf2.sctp ↗.reactivatePrimaryPath	bool	false
iUpf2.sctp ↗.sendQueueLimit	int	0
iUpf2.sctp ↗.validCookieLifetime	double	10s
iUpf2.sctp ↗.enableHeartbeats	bool	true
iUpf2.sctp ↗.hbInterval	double	30s
iUpf2.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
iUpf2.sctp ↗.nagleEnabled	bool	true
iUpf2.sctp ↗.naglePoint	int	1468
iUpf2.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
iUpf2.sctp ↗.fastRecoverySupported	bool	true
iUpf2.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
iUpf2.sctp ↗.ccModule	int	0	RFC4960=0
iUpf2.sctp ↗.osbWithHeader	bool	false
iUpf2.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
iUpf2.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
iUpf2.sctp ↗.arwnd	int	65535
iUpf2.sctp ↗.swsLimit	int	3000	Limit for SWS
iUpf2.sctp ↗.udpEncapsEnabled	bool	false
iUpf2.sctp ↗.natFriendly	bool	false
iUpf2.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
iUpf2.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
iUpf2.sctp ↗.tellArwnd	bool	false	For flow control
iUpf2.sctp ↗.messageAcceptLimit	int	0	For flow control
iUpf2.sctp ↗.fairStart	double	0s
iUpf2.sctp ↗.fairStop	double	0s
iUpf2.sctp ↗.streamsToPaths	string	“”
iUpf2.sctp ↗.startEndToEndDelay	int	0
iUpf2.sctp ↗.stopEndToEndDelay	int	10
iUpf2.sctp ↗.throughputInterval	double	1
iUpf2.sctp ↗.auth	bool	false
iUpf2.sctp ↗.chunks	string	“”
iUpf2.sctp ↗.padding	bool	false
iUpf2.sctp ↗.addIP	bool	false
iUpf2.sctp ↗.addTime	double	0s
iUpf2.sctp ↗.addAddress	string	“”
iUpf2.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
iUpf2.sctp ↗.packetDrop	bool	false
iUpf2.sctp ↗.sackNow	bool	false
iUpf2.sctp ↗.highSpeedCC	bool	false
iUpf2.sctp ↗.checkSackSeqNumber	bool	false
iUpf2.sctp ↗.nrSack	bool	false
iUpf2.sctp ↗.disableReneging	bool	false
iUpf2.sctp ↗.gapReportLimit	int	100000000
iUpf2.sctp ↗.gapListOptimizationVariant	string	“none”
iUpf2.sctp ↗.smartOverfullSACKHandling	bool	false
iUpf2.sctp ↗.allowQoSTracking	bool	false
iUpf2.sctp ↗.qosTrackingInterval	double	1.0s
iUpf2.sctp ↗.cmtSendAllVariant	string	“normal”
iUpf2.sctp ↗.cmtRetransmissionVariant	string	“normal”
iUpf2.sctp ↗.cmtCUCVariant	string	“normal”
iUpf2.sctp ↗.cmtBufferSplitVariant	string	“none”
iUpf2.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
iUpf2.sctp ↗.cmtUseSFR	bool	true
iUpf2.sctp ↗.cmtUseDAC	bool	true
iUpf2.sctp ↗.cmtUseFRC	bool	true
iUpf2.sctp ↗.cmtSmartT3Reset	bool	true
iUpf2.sctp ↗.cmtSmartFastRTX	bool	true
iUpf2.sctp ↗.cmtSmartReneging	bool	false
iUpf2.sctp ↗.cmtSlowPathRTTUpdate	bool	false
iUpf2.sctp ↗.cmtChunkReschedulingVariant	string	“none”
iUpf2.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
iUpf2.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
iUpf2.sctp ↗.movedChunkFastRTXFactor	double	2.0
iUpf2.sctp ↗.cmtSackPath	string	“standard”
iUpf2.sctp ↗.strictCwndBooking	bool	false
iUpf2.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
iUpf2.sctp ↗.cmtCCPathGroups	string	“”
iUpf2.sctp ↗.rpPathBlocking	bool	false
iUpf2.sctp ↗.rpScaleBlockingTimeout	bool	false
iUpf2.sctp ↗.rpMinCwnd	int	1
iUpf2.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.quic ↗.routingTableModule	string		Set by StandardHost.
iUpf2.quic ↗.sendZeroRttTokenAsServer	bool	false
iUpf2.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
iUpf2.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
iUpf2.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
iUpf2.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
iUpf2.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
iUpf2.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
iUpf2.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
iUpf2.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
iUpf2.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
iUpf2.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
iUpf2.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
iUpf2.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
iUpf2.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
iUpf2.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
iUpf2.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
iUpf2.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
iUpf2.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
iUpf2.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
iUpf2.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
iUpf2.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
iUpf2.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
iUpf2.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
iUpf2.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
iUpf2.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
iUpf2.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
iUpf2.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
iUpf2.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
iUpf2.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
iUpf2.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
iUpf2.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.tn ↗.forwardServiceRegistration	bool	true
iUpf2.tn ↗.forwardProtocolRegistration	bool	true
iUpf2.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.at ↗.forwardServiceRegistration	bool	true
iUpf2.at ↗.forwardProtocolRegistration	bool	true
iUpf2.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.dnPpp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnPpp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.dnPpp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.dnPpp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.dnPpp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.dnPpp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.dnPpp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.dnPpp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.dnPpp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.dnPpp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.dnPpp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.dnPpp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.dnPpp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnPpp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.dnPpp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.dnPpp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnPpp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
iUpf2.dnPpp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf2.dnPpp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf2.dnPpp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf2.dnPpp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf2.dnPpp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnPpp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
iUpf2.dnPpp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
iUpf2.dnPpp ↗.ppp ↗.mtu	int	4470B
iUpf2.dnPpp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
iUpf2.dnPpp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
iUpf2.relay.trafficFlowFilter.binderModule	string	“binder”
iUpf2.relay.trafficFlowFilter.fastForwarding	bool	true
iUpf2.relay.gtpUser.binderModule	string	“binder”
iUpf2.relay.gtpUser.localPort	int	31
iUpf2.relay.gtpUser.tunnelPeerPort	int	31
iUpf2.rd ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.rd ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.rd ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.nodeControl.binderModule	string	“binder”
iUpf2.nodeControl.gtpUserModule	string	“^.relay.gtpUser”
iUpf2.nodeControl.trafficFlowFilterModule	string	“^.relay.trafficFlowFilter”
iUpf2.nodeControl.ethernetBridgeModule	string	“^.ethBridge.sessionMux”	The node’s Ethernet session bridge (see EthernetSessionBridge), if it has one
iUpf2.nodeControl.unstructuredPrefix	string	“”	The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. “2001:db8:5::/64” or “10.5.0.0/16”; empty = the node anchors no Unstructured session (see the main comment)
iUpf2.nodeControl.unstructuredServer	string	“”	The application server the Unstructured sessions’ uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix
iUpf2.nodeControl.unstructuredServerPort	int	-1	The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions
iUpf2.nodeControl.unstructuredPort	int	-1	The UDP port the node receives the Unstructured sessions’ downlink on, and sends their uplink from; must be set for Unstructured sessions
iUpf2.ndResponder.binderModule	string	“binder”
iUpf2.ndResponder.linkLocalAddress	string	“fe80::1”	The router’s address on every session’s link
iUpf2.ndResponder.routerLifetime	double	9000s	Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)
iUpf2.ndResponder.curHopLimit	int	64	Cur Hop Limit in the Router Advertisements (0 = unspecified)
iUpf2.ndResponder.checksumMode	string	“declared”
iUpf2.ethBridge.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.macTable ↗.agingTime	double	120s
iUpf2.ethBridge.macTable ↗.forwardingTable	object	[]
iUpf2.ethBridge.macTable ↗.forwardingTableFile	string	“”
iUpf2.ethBridge.macTable ↗.interfaceTableModule	string
iUpf2.ethBridge.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
iUpf2.ethBridge.sessionMux.interfaceTableModule	string		The bridge’s interface table, which the session ports are registered in
iUpf2.ethBridge.sessionMux.macTableModule	string		The bridge’s MAC table, flushed of a released session’s port
iUpf2.ethBridge.sessionMux.portModuleType	string	“simu5g.corenetwork.ethernetSessionBridge.EthernetSessionPort”	The module type of the session ports
iUpf2.ethBridge.sessionMux.portDisplayString	string	“p=500,420,row,100;g=sessionPorts”	Display string of the session ports (their place in the bridge’s layout)
iUpf2.ethBridge.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ethBridge.cb ↗.forwardServiceRegistration	bool	true
iUpf2.ethBridge.cb ↗.forwardProtocolRegistration	bool	true
iUpf2.ethBridge.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ethBridge.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ethBridge.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.forwardProtocolRegistration	bool	true
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ethBridge.bridging ↗.directionReverser ↗.fork ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardVlan	bool	true
iUpf2.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardPcp	bool	true
iUpf2.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.excludeEncapsulationProtocols	object	[]
iUpf2.ethBridge.bridging ↗.directionReverser ↗.join ↗.displayStringTextFormat	string	“passed %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bridging ↗.directionReverser ↗.join ↗.forwardServiceRegistration	bool	true
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.macTableModule	string		Relative module path of MAC table
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.interfaceTableModule	string		Relative module path of the interface table
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.macTableModule	string		Relative module path of MAC table
iUpf2.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.interfaceTableModule	string		Relative module path of interface table
iUpf2.ethBridge.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ethBridge.bl ↗.forwardServiceRegistration	bool	true
iUpf2.ethBridge.bl ↗.forwardProtocolRegistration	bool	true
iUpf2.ethBridge.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ethBridge.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ethBridge.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.ethBridge.ethernet ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.socketCommandProcessor ↗.socketTableModule	string
iUpf2.ethBridge.ethernet ↗.macHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.macHeaderInserter ↗.interfaceTableModule	string
iUpf2.ethBridge.ethernet ↗.paddingInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.paddingInserter ↗.minLength	int
iUpf2.ethBridge.ethernet ↗.paddingInserter ↗.roundingLength	int	1B
iUpf2.ethBridge.ethernet ↗.paddingInserter ↗.insertionPosition	string	“back”
iUpf2.ethBridge.ethernet ↗.fcsInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.fcsInserter ↗.fcsMode	string	“declared”
iUpf2.ethBridge.ethernet ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.socketPacketProcessor ↗.socketTableModule	string
iUpf2.ethBridge.ethernet ↗.macHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.macHeaderChecker ↗.backpressure	bool	false
iUpf2.ethBridge.ethernet ↗.macHeaderChecker ↗.interfaceTableModule	string
iUpf2.ethBridge.ethernet ↗.macHeaderChecker ↗.promiscuous	bool	false
iUpf2.ethBridge.ethernet ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ethernet ↗.fcsChecker ↗.backpressure	bool	false
iUpf2.ethBridge.ethernet ↗.fcsChecker ↗.popFcs	bool	true
iUpf2.ethBridge.ieee8021q ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.socketTableModule	string
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.vlanTagType	string	“c”
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.nextProtocol	string	“ethernetmac”
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultVlanId	int	-1
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultPcp	int	-1
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultUserPriority	int	-1
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultDropEligible	int	-1	<0: unspecified, 0: false, >0: true
iUpf2.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.socketTableModule	string
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.backpressure	bool	false
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanTagType	string	“c”
iUpf2.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanIdFilter	object	[]
iUpf2.ethBridge.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.ethBridge.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
iUpf2.ethBridge.li ↗.forwardServiceRegistration	bool	true
iUpf2.ethBridge.li ↗.forwardProtocolRegistration	bool	true
iUpf2.ethBridge.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
iUpf2.ethBridge.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
iUpf2.ethBridge.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
iUpf2.dnEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
iUpf2.dnEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
iUpf2.dnEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
iUpf2.dnEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
iUpf2.dnEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
iUpf2.dnEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
iUpf2.dnEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
iUpf2.dnEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
iUpf2.dnEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
iUpf2.dnEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
iUpf2.dnEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
iUpf2.dnEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
iUpf2.dnEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
iUpf2.dnEth ↗.macLayer ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.macLayer ↗.queue ↗.packetCapacity	int	-1	Maximum number of packets in the queue, no limit by default
iUpf2.dnEth ↗.macLayer ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
iUpf2.dnEth ↗.macLayer ↗.queue ↗.dropperClass	string	“”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
iUpf2.dnEth ↗.macLayer ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
iUpf2.dnEth ↗.macLayer ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
iUpf2.dnEth ↗.macLayer ↗.server ↗.displayStringTextFormat	string	“served %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.macLayer ↗.server ↗.serveSchedulingPriority	int	0	Specifies the FES scheduling priority for the extra event that is pulling the packet, -1 means no extra event
iUpf2.dnEth ↗.macLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.macLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnEth ↗.macLayer ↗.outboundEmitter ↗.direction	string	“undefined”
iUpf2.dnEth ↗.macLayer ↗.outboundEmitter ↗.signalName	string
iUpf2.dnEth ↗.macLayer ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.macLayer ↗.fcsChecker ↗.backpressure	bool	false
iUpf2.dnEth ↗.macLayer ↗.fcsChecker ↗.popFcs	bool	false
iUpf2.dnEth ↗.macLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.macLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnEth ↗.macLayer ↗.inboundEmitter ↗.direction	string	“undefined”
iUpf2.dnEth ↗.macLayer ↗.inboundEmitter ↗.signalName	string
iUpf2.dnEth ↗.phyLayer ↗.phyHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.displayStringTextFormat	string	“delayed %p pk (%l)\nifg: %g”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
iUpf2.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.initialChannelBusy	bool	false	Assume that the channel was busy before the simulation started
iUpf2.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.duration	double	96s / dropUnit(parent.bitrate)
iUpf2.dnEth ↗.phyLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnEth ↗.phyLayer ↗.outboundEmitter ↗.direction	string	“undefined”
iUpf2.dnEth ↗.phyLayer ↗.outboundEmitter ↗.signalName	string
iUpf2.dnEth ↗.phyLayer ↗.transmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.transmitter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
iUpf2.dnEth ↗.phyLayer ↗.transmitter ↗.datarate	double	parent.bitrate
iUpf2.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.backpressure	bool	false
iUpf2.dnEth ↗.phyLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
iUpf2.dnEth ↗.phyLayer ↗.inboundEmitter ↗.direction	string	“undefined”
iUpf2.dnEth ↗.phyLayer ↗.inboundEmitter ↗.signalName	string
iUpf2.dnEth ↗.phyLayer ↗.receiver ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
iUpf2.dnEth ↗.phyLayer ↗.receiver ↗.datarate	double	parent.bitrate
gnb1.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
gnb1.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
gnb1.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
gnb1.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
gnb1.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
gnb1.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
gnb1.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
gnb1.mobility ↗.initialLatitude	double	nan deg
gnb1.mobility ↗.initialLongitude	double	nan deg
gnb1.mobility ↗.initialAltitude	double	0m
gnb1.mobility ↗.initialHeading	double	0deg
gnb1.mobility ↗.initialElevation	double	0deg
gnb1.mobility ↗.initialBank	double	0deg
gnb1.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
gnb1.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
gnb1.cellInfo.constraintAreaMinX	double	-1m/0	The minimum X-coordinate of the area constraint, unconstrained by default
gnb1.cellInfo.constraintAreaMinY	double	-1m/0	The minimum Y-coordinate of the area constraint, unconstrained by default
gnb1.cellInfo.constraintAreaMaxX	double	1m/0	The maximum X-coordinate of the area constraint, unconstrained by default
gnb1.cellInfo.constraintAreaMaxY	double	1m/0	The maximum Y-coordinate of the area constraint, unconstrained by default
gnb1.cellInfo.beaconInterval	double	1s	Interval for sending broadcast messages (used for handover or DAS)
gnb1.cellInfo.microCell	bool	false	Type of eNodeB (MICRO / MACRO) - valid only for eNodeBs
gnb1.cellInfo.rbyDl	int	12	Number of sub-carriers per RB in DL
gnb1.cellInfo.rbyUl	int	12	Number of sub-carriers per RB in UL
gnb1.cellInfo.rbxDl	int	7	Number of OFDM symbols per slot in DL
gnb1.cellInfo.rbxUl	int	7	Number of OFDM symbols per slot in UL
gnb1.cellInfo.rbPilotDl	int	3	Number of pilot Resource Elements per RB in DL
gnb1.cellInfo.rbPilotUl	int	0	Number of pilot Resource Elements per RB in UL
gnb1.cellInfo.signalDl	int	1	Number of signaling symbols for each Resource Block in DL
gnb1.cellInfo.signalUl	int	1	Number of signaling symbols for each Resource Block in UL
gnb1.cellInfo.numPreferredBands	int	1	Number of preferred bands to use (relevant only in PREFERRED mode)
gnb1.cellInfo.binderModule	string	“binder”
gnb1.cellularNic.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.cellularNic.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb1.cellularNic.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb1.cellularNic.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb1.cellularNic.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb1.cellularNic.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb1.cellularNic.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb1.cellularNic.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb1.cellularNic.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb1.cellularNic.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb1.cellularNic.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb1.cellularNic.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb1.cellularNic.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb1.cellularNic.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb1.cellularNic.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb1.cellularNic.handoverPacketHolder.binderModule	string	“binder”
gnb1.cellularNic.ip2nic.binderModule	string	“binder”
gnb1.cellularNic.ip2nic.connectionControlModule	string	“^.rrc.connectionControl”	The node’s control-plane entry point, asked for a bearer on a lookup miss
gnb1.cellularNic.ip2nic.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb, or in the ini for a DC master eNB)
gnb1.cellularNic.ip2nic.hasSdap	bool	false	When true, SDAP handles DRB/RLC assignment; Ip2Nic skips traffic classification
gnb1.cellularNic.ip2nic.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe), which the payload the NIC delivers up is of; set by the NIC
gnb1.cellularNic.ip2nic.establishBearersOnDemand	bool	true	When false, a packet that finds no established bearer raises an error instead of establishing one (static bearers are established up front; see the staticDrbs parameter of BearerConfigurator)
gnb1.cellularNic.ip2nic.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
gnb1.cellularNic.rrc.registration.interfaceTableModule	string
gnb1.cellularNic.rrc.registration.interfaceName	string	“cellular”
gnb1.cellularNic.rrc.registration.routingTableModule	string
gnb1.cellularNic.rrc.registration.binderModule	string	“binder”
gnb1.cellularNic.rrc.registration.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), told about a multicast group join
gnb1.cellularNic.rrc.registration.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe): a UE created during the run gets an IPv4 default route through the NIC only on an IP session, and the NIC of an Ethernet session is an Ethernet port; set by the NIC
gnb1.cellularNic.rrc.bearerManagement.binderModule	string	“binder”	To reach a peer’s BearerManagement on RLF
gnb1.cellularNic.rrc.bearerManagement.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), which a torn-down bearer’s DRB identity goes back through
gnb1.cellularNic.rrc.bearerManagement.t311	double	0s	RRC re-establishment cell-selection timer (0 => release-to-IDLE)
gnb1.cellularNic.rrc.bearerManagement.t301	double	0.1s	RRC re-establishment (request -> complete) timer
gnb1.cellularNic.rrc.bearerManagement.headerCompressedSize	int	-1B	Removed, an error if set: header compression is configured per bearer (the rohc field of BearerConfigurator’s bearer definitions)
gnb1.cellularNic.rrc.bearerManagement.pdcpEntityModuleType	string	“simu5g.stack.pdcp.LtePdcpEntity”	PDCP entity types: the full PDCP entity is a compound (PdcpEntityBase, TX+RX sides plus the leg split/join stage of a multi-leg bearer); the instantiable types are its subclasses (LtePdcpEntity, NrPdcpEntity). At a DC secondary a bearer’s PDCP lives at the master, so the secondary installs an PdcpRelayEntity (tunnels PDUs to/from the master) in its place.
gnb1.cellularNic.rrc.bearerManagement.pdcpRelayEntityModuleType	string	“simu5g.stack.pdcp.PdcpRelayEntity”
gnb1.cellularNic.rrc.bearerManagement.dualConnectivityEnabled	bool	false	Set by the NIC; two-leg (split-capable) bearers
gnb1.cellularNic.rrc.bearerManagement.rlcTmEntityModuleType	string	“simu5g.stack.rlc.RlcTmEntity”	RLC entity types (compound modules): lteRlc* = LTE-FI bearers (TS 36.322), nrRlc* = NR bearers (SI/SO wire format, TS 38.322)
gnb1.cellularNic.rrc.bearerManagement.lteRlcUmEntityModuleType	string	“simu5g.stack.rlc.LteRlcUmEntity”
gnb1.cellularNic.rrc.bearerManagement.lteRlcAmEntityModuleType	string	“simu5g.stack.rlc.LteRlcAmEntity”
gnb1.cellularNic.rrc.bearerManagement.nrRlcUmEntityModuleType	string	“simu5g.stack.rlc.NrRlcUmEntity”
gnb1.cellularNic.rrc.bearerManagement.nrRlcAmEntityModuleType	string	“simu5g.stack.rlc.NrRlcAmEntity”
gnb1.cellularNic.rrc.bearerManagement.registrationModule	string	“^.registration”	Module references for accessing other stack layers
gnb1.cellularNic.rrc.bearerManagement.drbTableModule	string	“^.drbTable”
gnb1.cellularNic.rrc.bearerManagement.ip2nicModule	string	“^.^.ip2nic”
gnb1.cellularNic.rrc.bearerManagement.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”	Attachment-ledger push target (UE only)
gnb1.cellularNic.rrc.bearerManagement.pdcpMuxModule	string	“^.^.pdcpMux”
gnb1.cellularNic.rrc.bearerManagement.pdcpDcMuxModule	string	“^.^.pdcpDcMux”
gnb1.cellularNic.rrc.bearerManagement.d2dModeControllerModule	string	“^.d2dModeController”
gnb1.cellularNic.rrc.bearerManagement.rlcMuxModule	string	“^.^.rlcMux”
gnb1.cellularNic.rrc.bearerManagement.nrRlcMuxModule	string	“^.^.nrRlcMux”
gnb1.cellularNic.rrc.bearerManagement.macModule	string	“^.^.mac”
gnb1.cellularNic.rrc.bearerManagement.nrMacModule	string	“^.^.nrMac”
gnb1.cellularNic.rrc.bearerManagement.sdapModule	string	“^.^.sdap”	Configuration push target; unresolvable (no SDAP on the NIC) = no pushes
gnb1.cellularNic.rrc.bearerManagement.qosFlowClassifierModule	string	“^.^.qosFlowClassifier”	Uplink QFI rule push target; unresolvable (not a UE stack with SDAP) = no pushes
gnb1.cellularNic.rrc.connectionControl.binderModule	string	“binder”
gnb1.cellularNic.rrc.connectionControl.bearerConfiguratorModule	string	“bearerConfigurator”
gnb1.cellularNic.rrc.connectionControl.coreControlModule	string	“coreControl”
gnb1.cellularNic.rrc.connectionControl.bearerManagementModule	string	“^.bearerManagement”
gnb1.cellularNic.rrc.connectionControl.macModule	string	“^.^.mac”
gnb1.cellularNic.rrc.connectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
gnb1.cellularNic.rrc.connectionControl.gtpUserModule	string	“^.^.^.relay.gtpUser”
gnb1.cellularNic.rrc.connectionControl.gtpUserX2Module	string	“^.^.^.gtpUserX2”
gnb1.cellularNic.rrc.connectionControl.macNodeId	int		The base station’s node id; the NIC sets it from the node’s
gnb1.cellularNic.rrc.connectionControl.gateway	string	“”	The node’s core network gateway, as its gateway parameter names it; ignored at a node not connected to a core network (a secondary node)
gnb1.cellularNic.rrc.nrConnectionControl.dynamicCellAssociation	bool	false
gnb1.cellularNic.rrc.nrConnectionControl.enableHandover	bool	false	Allows handovers in the UE
gnb1.cellularNic.rrc.nrConnectionControl.isNr	bool		Whether this instance is associated with the NR or the LTE stack
gnb1.cellularNic.rrc.nrConnectionControl.macNodeId	int		MacNodeId of the stack leg this controller belongs to (set by the NIC)
gnb1.cellularNic.rrc.nrConnectionControl.sessionType	string		The type of the session the UE requests at connection setup (see LteUe), set by the NIC
gnb1.cellularNic.rrc.nrConnectionControl.handoverLatency	double	50ms	Handover duration
gnb1.cellularNic.rrc.nrConnectionControl.handoverDetachmentTime	double	handoverLatency > 0s ? handoverLatency/2 : 25ms
gnb1.cellularNic.rrc.nrConnectionControl.handoverAttachmentTime	double	handoverLatency > 0s ? handoverLatency-handoverDetachmentTime : handoverDetachmentTime
gnb1.cellularNic.rrc.nrConnectionControl.minRssiDefault	bool	true	Whether minRssi is taken from PhyPisaData instead of the minRssi parameter
gnb1.cellularNic.rrc.nrConnectionControl.minRssi	double	-99.0dB	Configurable minimum threshold RSSI for attaching to an eNB (meaningful only if minRssiDefault==false)
gnb1.cellularNic.rrc.nrConnectionControl.hysteresisFactor	double	10
gnb1.cellularNic.rrc.nrConnectionControl.binderModule	string	“binder”
gnb1.cellularNic.rrc.nrConnectionControl.macModule	string	“^.^.mac”
gnb1.cellularNic.rrc.nrConnectionControl.bearerManagementModule	string	“^.bearerManagement”
gnb1.cellularNic.rrc.nrConnectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
gnb1.cellularNic.rrc.nrConnectionControl.feedbackGeneratorModule	string	“^.^.dlFbGen”	TODO or “^.^.nrDlFbGen”
gnb1.cellularNic.rrc.nrConnectionControl.otherConnectionControlModule	string	“”
gnb1.cellularNic.rrc.nrConnectionControl.hasCollector	bool	false	True when node has a collector module (ueCollector/nrUeCollector) for this PHY module
gnb1.cellularNic.rrc.d2dModeSelection.modeSelectionPeriod	double	1s
gnb1.cellularNic.rrc.d2dModeSelection.binderModule	string	“binder”
gnb1.cellularNic.rrc.d2dModeSelection.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
gnb1.cellularNic.rrc.d2dModeSelection.macModule	string	“^.^.mac”
gnb1.cellularNic.rrc.d2dModeSelection.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point, which knows the UEs handing over
gnb1.cellularNic.rlcMux.bearerManagementModule	string	“^.rrc.bearerManagement”
gnb1.cellularNic.phy.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb on their PHY submodule)
gnb1.cellularNic.phy.macNodeId	int		MacNodeId of the stack leg this PHY belongs to (set by the NIC)
gnb1.cellularNic.phy.ueTxPower	double	26dBm
gnb1.cellularNic.phy.eNodeBTxPower	double	46dBm
gnb1.cellularNic.phy.microTxPower	double	30dBm
gnb1.cellularNic.phy.txDirection	string	“OMNI”
gnb1.cellularNic.phy.txAngle	double	0deg
gnb1.cellularNic.phy.binderModule	string	“binder”
gnb1.cellularNic.phy.channelModelModule	string	“^.channelModel[0]”	Set to “^.nrChannelModel[0]” on an NR leg, see NrNicUe
gnb1.cellularNic.phy.enableHandover	bool	false	Marks this eNB as a handover target: its beacons are used by UEs for handover feasibility assessment. Requires enableBeacons=true (the default when handover is on); the module errors out at initialization if beacons are disabled while handover is enabled.
gnb1.cellularNic.phy.enableBeacons	bool	enableHandover	Enables broadcasting periodic beacons (at cellInfo.beaconInterval). Beacons are the measurement signal UEs use both for handover feasibility assessment and for radio link monitoring (RLF detection), decoupled from enableHandover so radio link monitoring can run without handover. Defaults to enableHandover (beacons flow exactly when handover is enabled). cellInfo.beaconInterval must be positive: a zero/negative interval is an error – switch beacons off with enableBeacons=false.
gnb1.cellularNic.phy.targetBler	double	0.001
gnb1.cellularNic.packetFlowObserver.macModule	string	“^.mac”
gnb1.cellularNic.packetFlowObserver.pdcpModule	string	“^”
gnb1.cellularNic.packetFlowObserver.rlcModule	string	“^”
gnb1.cellularNic.packetFlowObserver.isNrObserver	bool	false
gnb1.cellularNic.packetFlowObserver.pfmType	string	“PacketFlowObserverEnb”
gnb1.cellularNic.pdcpDcMux.bearerManagementModule	string	“^.rrc.bearerManagement”
gnb1.cellularNic.x2Manager.interfaceTableModule	string
gnb1.cellularNic.x2Manager.binderModule	string	“binder”
gnb1.cellularNic.compManager.compNodeType	string	“COMP_CLIENT”
gnb1.cellularNic.compManager.coordinatorId	int		ID of the coordinator node
gnb1.cellularNic.compManager.clientList	object	[]	Space-separated list of client node identifiers
gnb1.cellularNic.compManager.coordinationPeriod	double	0.001s	The time interval between two coordination events
gnb1.cellularNic.compManager.binderModule	string	“binder”
gnb1.cellularNic.handoverX2Forwarder.losslessHandover	bool	false
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialLatitude	double	nan deg
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialLongitude	double	nan deg
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialAltitude	double	0m
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialHeading	double	0deg
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialElevation	double	0deg
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialBank	double	0deg
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
gnb1.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.computeAvgInterference	bool
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.enablePeriodicCqiUpdate	bool
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.useProbabilisticCqi	bool
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.backgroundTrafficManagerModule	string	“^.^.manager”
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.startTimeDl	double	-1s
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.startTimeUl	double	-1s
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.headerLen	int	33B
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.txPower	double	26dBm
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.fbPeriod	int	6tti
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.periodDl	double	uniform(10ms,50ms)
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.periodUl	double	uniform(10ms,50ms)
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.packetSizeDl	int	intuniform(20B,100B)
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.packetSizeUl	int	intuniform(20B,100B)
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.rtxRateDl	double	0.1
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.rtxDelayDl	double	0.006s
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.rtxRateUl	double	0.1
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.rtxDelayUl	double	0.006s
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.cqiMeanDl	double	15	These values are only considered when periodicCqi == false && computeAvgInterference == false
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.cqiMeanUl	double	15
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.cqiStddevDl	double	0
gnb1.cellularNic.bgTrafficGenerator.bgUE.generator.cqiStddevUl	double	0
gnb1.cellularNic.bgTrafficGenerator.manager.binderModule	string	“binder”
gnb1.cellularNic.bgTrafficGenerator.manager.numBgUes	int
gnb1.cellularNic.bgTrafficGenerator.manager.macModule	string	“^.^.mac”
gnb1.cellularNic.bgTrafficGenerator.manager.phyModule	string	“^.^.phy”
gnb1.cellularNic.bgTrafficGenerator.manager.enablePeriodicCqiUpdate	bool
gnb1.cellularNic.bgTrafficGenerator.manager.computeAvgInterference	bool
gnb1.pppIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb1.pppIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb1.pppIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb1.pppIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb1.pppIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb1.pppIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb1.pppIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb1.pppIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb1.pppIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb1.pppIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb1.pppIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb1.pppIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb1.pppIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb1.pppIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb1.pppIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb1.pppIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb1.pppIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb1.pppIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb1.pppIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb1.pppIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.pppIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb1.pppIf ↗.ppp ↗.mtu	int	4470B
gnb1.pppIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb1.pppIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb1.x2ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.x2ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb1.x2ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb1.x2ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb1.x2ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb1.x2ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb1.x2ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb1.x2ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb1.x2ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb1.x2ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb1.x2ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb1.x2ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb1.x2ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb1.x2ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb1.x2ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb1.x2ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.x2ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb1.x2ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb1.x2ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb1.x2ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb1.x2ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb1.x2ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.x2ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.x2ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb1.x2ppp ↗.ppp ↗.mtu	int	4470B
gnb1.x2ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb1.x2ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb1.pppMEHostIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppMEHostIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb1.pppMEHostIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb1.pppMEHostIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb1.pppMEHostIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb1.pppMEHostIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb1.pppMEHostIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb1.pppMEHostIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb1.pppMEHostIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb1.pppMEHostIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb1.pppMEHostIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb1.pppMEHostIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb1.pppMEHostIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb1.pppMEHostIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb1.pppMEHostIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb1.pppMEHostIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppMEHostIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb1.pppMEHostIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb1.pppMEHostIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb1.pppMEHostIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb1.pppMEHostIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb1.pppMEHostIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.pppMEHostIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.pppMEHostIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb1.pppMEHostIf ↗.ppp ↗.mtu	int	4470B
gnb1.pppMEHostIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb1.pppMEHostIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb1.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.configurator ↗.routingTableModule	string
gnb1.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
gnb1.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
gnb1.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
gnb1.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
gnb1.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
gnb1.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
gnb1.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
gnb1.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
gnb1.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
gnb1.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
gnb1.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
gnb1.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
gnb1.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.igmp ↗.routingTableModule	string
gnb1.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
gnb1.ipv4 ↗.igmp ↗.enabled	bool	true
gnb1.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
gnb1.ipv4 ↗.igmp ↗.queryInterval	double	125s
gnb1.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
gnb1.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
gnb1.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
gnb1.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
gnb1.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
gnb1.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
gnb1.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
gnb1.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
gnb1.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.icmp ↗.routingTableModule	string
gnb1.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
gnb1.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
gnb1.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
gnb1.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
gnb1.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.ip ↗.routingTableModule	string
gnb1.ipv4 ↗.ip ↗.arpModule	string
gnb1.ipv4 ↗.ip ↗.icmpModule	string
gnb1.ipv4 ↗.ip ↗.checksumMode	string	“declared”
gnb1.ipv4 ↗.ip ↗.timeToLive	int	32
gnb1.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
gnb1.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
gnb1.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
gnb1.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
gnb1.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
gnb1.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
gnb1.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
gnb1.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv4 ↗.arp ↗.routingTableModule	string
gnb1.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
gnb1.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
gnb1.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
gnb1.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
gnb1.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
gnb1.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
gnb1.ipv4 ↗.ipsec ↗.interfaceTableModule	string
gnb1.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
gnb1.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
gnb1.ipv4 ↗.ipsec ↗.spdConfig	xml
gnb1.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
gnb1.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
gnb1.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
gnb1.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
gnb1.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
gnb1.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
gnb1.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
gnb1.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
gnb1.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
gnb1.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
gnb1.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
gnb1.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.configurator ↗.interfaceTableModule	string
gnb1.ipv6 ↗.configurator ↗.routingTableModule	string
gnb1.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
gnb1.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
gnb1.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
gnb1.ipv6 ↗.routingTable ↗.forwarding	bool	false
gnb1.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
gnb1.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
gnb1.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
gnb1.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
gnb1.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
gnb1.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
gnb1.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
gnb1.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
gnb1.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
gnb1.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
gnb1.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
gnb1.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
gnb1.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
gnb1.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
gnb1.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
gnb1.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
gnb1.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
gnb1.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
gnb1.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
gnb1.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
gnb1.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
gnb1.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
gnb1.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
gnb1.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
gnb1.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
gnb1.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
gnb1.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
gnb1.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
gnb1.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv6 ↗.ipv6 ↗.routingTableModule	string
gnb1.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
gnb1.ipv6 ↗.ipv6 ↗.icmpv6Module	string
gnb1.ipv6 ↗.ipv6 ↗.procDelay	double	0s
gnb1.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
gnb1.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.ipsec ↗.interfaceTableModule	string
gnb1.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
gnb1.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
gnb1.ipv6 ↗.ipsec ↗.spdConfig	xml
gnb1.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
gnb1.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
gnb1.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
gnb1.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
gnb1.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
gnb1.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
gnb1.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
gnb1.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
gnb1.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
gnb1.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
gnb1.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
gnb1.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
gnb1.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
gnb1.ipv6 ↗.mipv6 ↗.isMobileNode	bool
gnb1.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
gnb1.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
gnb1.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
gnb1.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
gnb1.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
gnb1.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
gnb1.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
gnb1.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
gnb1.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
gnb1.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
gnb1.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
gnb1.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
gnb1.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
gnb1.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
gnb1.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
gnb1.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
gnb1.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
gnb1.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
gnb1.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
gnb1.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
gnb1.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
gnb1.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
gnb1.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
gnb1.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
gnb1.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
gnb1.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb1.udp ↗.checksumMode	string	“declared”
gnb1.udp ↗.defaultMulticastLoop	bool	true
gnb1.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.tcp ↗.checksumMode	string	“declared”
gnb1.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
gnb1.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
gnb1.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
gnb1.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
gnb1.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
gnb1.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
gnb1.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
gnb1.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
gnb1.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
gnb1.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
gnb1.tcp ↗.msl	int	120s	Maximum Segment Lifetime
gnb1.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
gnb1.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
gnb1.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
gnb1.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
gnb1.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb1.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
gnb1.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
gnb1.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
gnb1.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
gnb1.x2App.client.displayStringTextFormat	string	“{socketState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.x2App.client.localAddress	string	“”	Comma-separated list of addresses
gnb1.x2App.client.localPort	int	0	Port number to listen on
gnb1.x2App.client.connectAddress	string		Server address (may be symbolic)
gnb1.x2App.client.connectPort	int	5000	Port number to connect to
gnb1.x2App.client.startTime	double	0s	Time the first session begins
gnb1.x2App.client.numRequestsPerSession	int	1	Number of requests sent per session
gnb1.x2App.client.numPacketsToReceive	int	0
gnb1.x2App.client.requestLength	int	1452	Length of a request (bytes)
gnb1.x2App.client.thinkTime	double	0s	Time gap between requests
gnb1.x2App.client.waitToClose	double	0s	Time to wait between the last message sent and abort
gnb1.x2App.client.reconnectInterval	double	0s	If the connection breaks, waits this much before trying to reconnect
gnb1.x2App.client.inboundStreams	int	17
gnb1.x2App.client.outboundStreams	int	1
gnb1.x2App.client.echo	bool	false	Echoes received packages when true
gnb1.x2App.client.ordered	bool	true
gnb1.x2App.client.queueSize	int	0
gnb1.x2App.client.prMethod	int	0	0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST
gnb1.x2App.client.prValue	double	0	For PR-SCTP
gnb1.x2App.client.streamReset	bool	false
gnb1.x2App.client.streamRequestTime	double	0s
gnb1.x2App.client.streamResetType	int	5	NO_RESET=5, RESET_OUTGOING=6, RESET_INCOMING=7, RESET_BOTH=8, SSN_TSN=9
gnb1.x2App.client.streamToReset	int	0
gnb1.x2App.client.stopTime	double	-1s	Time of finishing sending, negative values mean forever
gnb1.x2App.client.primaryTime	double	0s
gnb1.x2App.client.newPrimary	string	“”
gnb1.x2App.client.streamRequestLengths	string	“”
gnb1.x2App.client.streamRequestRatio	string	“”
gnb1.x2App.client.streamPriorities	string	“”
gnb1.x2App.client.finishEndsSimulation	bool	false
gnb1.x2App.client.binderModule	string	“binder”
gnb1.x2App.server.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.x2App.server.localAddress	string	“”	Comma-separated list of addresses
gnb1.x2App.server.localPort	int	0	Port number to listen on
gnb1.x2App.server.echo	bool	false	Echoes received packages when true
gnb1.x2App.server.echoDelay	double	0s
gnb1.x2App.server.delayFirstRead	double	0s
gnb1.x2App.server.readingInterval	double	0s
gnb1.x2App.server.messagesToPush	int	0
gnb1.x2App.server.numPacketsToSendPerClient	int	0	Number of requests sent per session
gnb1.x2App.server.numPacketsToReceivePerClient	int	1
gnb1.x2App.server.requestLength	int	1452	Length of a request (bytes)
gnb1.x2App.server.thinkTime	double	0s	Time gap between requests
gnb1.x2App.server.waitToClose	double	0s	Time to wait between last message sent and abort
gnb1.x2App.server.finishEndsSimulation	bool	false
gnb1.x2App.server.ordered	bool	true
gnb1.x2App.server.inboundStreams	int	17
gnb1.x2App.server.outboundStreams	int	1
gnb1.x2App.server.queueSize	int	0
gnb1.x2App.server.prMethod	int	0	0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST
gnb1.x2App.server.prValue	double	0	For PR-SCTP
gnb1.x2App.server.streamReset	bool	false
gnb1.x2App.server.streamRequestTime	double	0s
gnb1.x2App.server.streamToReset	int	0
gnb1.x2App.server.streamPriorities	string	“”
gnb1.x2App.server.binderModule	string	“binder”
gnb1.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.sctp ↗.interfaceTableModule	string
gnb1.sctp ↗.routingTableModule	string
gnb1.sctp ↗.checksumMode	string	“declared”
gnb1.sctp ↗.numGapReports	int	3
gnb1.sctp ↗.rtoInitial	double	3s
gnb1.sctp ↗.rtoMin	double	1s
gnb1.sctp ↗.rtoMax	double	60s
gnb1.sctp ↗.rtoAlpha	double	0.125
gnb1.sctp ↗.rtoBeta	double	0.250
gnb1.sctp ↗.maxBurst	int	4
gnb1.sctp ↗.maxBurstVariant	string	“maxBurst”
gnb1.sctp ↗.initialWindow	int	0
gnb1.sctp ↗.assocMaxRetrans	int	10
gnb1.sctp ↗.pathMaxRetrans	int	5
gnb1.sctp ↗.maxInitRetrans	int	8
gnb1.sctp ↗.sackPeriod	double	200ms
gnb1.sctp ↗.sackFrequency	int	2
gnb1.sctp ↗.reactivatePrimaryPath	bool	false
gnb1.sctp ↗.sendQueueLimit	int	0
gnb1.sctp ↗.validCookieLifetime	double	10s
gnb1.sctp ↗.enableHeartbeats	bool	true
gnb1.sctp ↗.hbInterval	double	30s
gnb1.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
gnb1.sctp ↗.nagleEnabled	bool	true
gnb1.sctp ↗.naglePoint	int	1468
gnb1.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
gnb1.sctp ↗.fastRecoverySupported	bool	true
gnb1.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
gnb1.sctp ↗.ccModule	int	0	RFC4960=0
gnb1.sctp ↗.osbWithHeader	bool	false
gnb1.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
gnb1.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
gnb1.sctp ↗.arwnd	int	65535
gnb1.sctp ↗.swsLimit	int	3000	Limit for SWS
gnb1.sctp ↗.udpEncapsEnabled	bool	false
gnb1.sctp ↗.natFriendly	bool	false
gnb1.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
gnb1.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
gnb1.sctp ↗.tellArwnd	bool	false	For flow control
gnb1.sctp ↗.messageAcceptLimit	int	0	For flow control
gnb1.sctp ↗.fairStart	double	0s
gnb1.sctp ↗.fairStop	double	0s
gnb1.sctp ↗.streamsToPaths	string	“”
gnb1.sctp ↗.startEndToEndDelay	int	0
gnb1.sctp ↗.stopEndToEndDelay	int	10
gnb1.sctp ↗.throughputInterval	double	1
gnb1.sctp ↗.auth	bool	false
gnb1.sctp ↗.chunks	string	“”
gnb1.sctp ↗.padding	bool	false
gnb1.sctp ↗.addIP	bool	false
gnb1.sctp ↗.addTime	double	0s
gnb1.sctp ↗.addAddress	string	“”
gnb1.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
gnb1.sctp ↗.packetDrop	bool	false
gnb1.sctp ↗.sackNow	bool	false
gnb1.sctp ↗.highSpeedCC	bool	false
gnb1.sctp ↗.checkSackSeqNumber	bool	false
gnb1.sctp ↗.nrSack	bool	false
gnb1.sctp ↗.disableReneging	bool	false
gnb1.sctp ↗.gapReportLimit	int	100000000
gnb1.sctp ↗.gapListOptimizationVariant	string	“none”
gnb1.sctp ↗.smartOverfullSACKHandling	bool	false
gnb1.sctp ↗.allowQoSTracking	bool	false
gnb1.sctp ↗.qosTrackingInterval	double	1.0s
gnb1.sctp ↗.cmtSendAllVariant	string	“normal”
gnb1.sctp ↗.cmtRetransmissionVariant	string	“normal”
gnb1.sctp ↗.cmtCUCVariant	string	“normal”
gnb1.sctp ↗.cmtBufferSplitVariant	string	“none”
gnb1.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
gnb1.sctp ↗.cmtUseSFR	bool	true
gnb1.sctp ↗.cmtUseDAC	bool	true
gnb1.sctp ↗.cmtUseFRC	bool	true
gnb1.sctp ↗.cmtSmartT3Reset	bool	true
gnb1.sctp ↗.cmtSmartFastRTX	bool	true
gnb1.sctp ↗.cmtSmartReneging	bool	false
gnb1.sctp ↗.cmtSlowPathRTTUpdate	bool	false
gnb1.sctp ↗.cmtChunkReschedulingVariant	string	“none”
gnb1.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
gnb1.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
gnb1.sctp ↗.movedChunkFastRTXFactor	double	2.0
gnb1.sctp ↗.cmtSackPath	string	“standard”
gnb1.sctp ↗.strictCwndBooking	bool	false
gnb1.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
gnb1.sctp ↗.cmtCCPathGroups	string	“”
gnb1.sctp ↗.rpPathBlocking	bool	false
gnb1.sctp ↗.rpScaleBlockingTimeout	bool	false
gnb1.sctp ↗.rpMinCwnd	int	1
gnb1.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.at ↗.forwardServiceRegistration	bool	true
gnb1.at ↗.forwardProtocolRegistration	bool	true
gnb1.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.tn ↗.forwardServiceRegistration	bool	true
gnb1.tn ↗.forwardProtocolRegistration	bool	true
gnb1.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb1.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb1.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb1.nl ↗.forwardServiceRegistration	bool	true
gnb1.nl ↗.forwardProtocolRegistration	bool	true
gnb1.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb1.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb1.relay.trafficFlowFilter.binderModule	string	“binder”
gnb1.relay.trafficFlowFilter.fastForwarding	bool	true
gnb1.relay.gtpUser.binderModule	string	“binder”
gnb1.relay.gtpUser.localPort	int	31
gnb1.relay.gtpUser.tunnelPeerPort	int	31
gnb1.gtpUserX2.binderModule	string	“binder”
gnb1.gtpUserX2.localPort	int	32
gnb1.gtpUserX2.tunnelPeerPort	int	32
gnb2.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
gnb2.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
gnb2.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
gnb2.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
gnb2.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
gnb2.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
gnb2.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
gnb2.mobility ↗.initialLatitude	double	nan deg
gnb2.mobility ↗.initialLongitude	double	nan deg
gnb2.mobility ↗.initialAltitude	double	0m
gnb2.mobility ↗.initialHeading	double	0deg
gnb2.mobility ↗.initialElevation	double	0deg
gnb2.mobility ↗.initialBank	double	0deg
gnb2.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
gnb2.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
gnb2.cellInfo.constraintAreaMinX	double	-1m/0	The minimum X-coordinate of the area constraint, unconstrained by default
gnb2.cellInfo.constraintAreaMinY	double	-1m/0	The minimum Y-coordinate of the area constraint, unconstrained by default
gnb2.cellInfo.constraintAreaMaxX	double	1m/0	The maximum X-coordinate of the area constraint, unconstrained by default
gnb2.cellInfo.constraintAreaMaxY	double	1m/0	The maximum Y-coordinate of the area constraint, unconstrained by default
gnb2.cellInfo.beaconInterval	double	1s	Interval for sending broadcast messages (used for handover or DAS)
gnb2.cellInfo.microCell	bool	false	Type of eNodeB (MICRO / MACRO) - valid only for eNodeBs
gnb2.cellInfo.rbyDl	int	12	Number of sub-carriers per RB in DL
gnb2.cellInfo.rbyUl	int	12	Number of sub-carriers per RB in UL
gnb2.cellInfo.rbxDl	int	7	Number of OFDM symbols per slot in DL
gnb2.cellInfo.rbxUl	int	7	Number of OFDM symbols per slot in UL
gnb2.cellInfo.rbPilotDl	int	3	Number of pilot Resource Elements per RB in DL
gnb2.cellInfo.rbPilotUl	int	0	Number of pilot Resource Elements per RB in UL
gnb2.cellInfo.signalDl	int	1	Number of signaling symbols for each Resource Block in DL
gnb2.cellInfo.signalUl	int	1	Number of signaling symbols for each Resource Block in UL
gnb2.cellInfo.numPreferredBands	int	1	Number of preferred bands to use (relevant only in PREFERRED mode)
gnb2.cellInfo.binderModule	string	“binder”
gnb2.cellularNic.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.cellularNic.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb2.cellularNic.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb2.cellularNic.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb2.cellularNic.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb2.cellularNic.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb2.cellularNic.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb2.cellularNic.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb2.cellularNic.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb2.cellularNic.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb2.cellularNic.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb2.cellularNic.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb2.cellularNic.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb2.cellularNic.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb2.cellularNic.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb2.cellularNic.handoverPacketHolder.binderModule	string	“binder”
gnb2.cellularNic.ip2nic.binderModule	string	“binder”
gnb2.cellularNic.ip2nic.connectionControlModule	string	“^.rrc.connectionControl”	The node’s control-plane entry point, asked for a bearer on a lookup miss
gnb2.cellularNic.ip2nic.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb, or in the ini for a DC master eNB)
gnb2.cellularNic.ip2nic.hasSdap	bool	false	When true, SDAP handles DRB/RLC assignment; Ip2Nic skips traffic classification
gnb2.cellularNic.ip2nic.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe), which the payload the NIC delivers up is of; set by the NIC
gnb2.cellularNic.ip2nic.establishBearersOnDemand	bool	true	When false, a packet that finds no established bearer raises an error instead of establishing one (static bearers are established up front; see the staticDrbs parameter of BearerConfigurator)
gnb2.cellularNic.ip2nic.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
gnb2.cellularNic.rrc.registration.interfaceTableModule	string
gnb2.cellularNic.rrc.registration.interfaceName	string	“cellular”
gnb2.cellularNic.rrc.registration.routingTableModule	string
gnb2.cellularNic.rrc.registration.binderModule	string	“binder”
gnb2.cellularNic.rrc.registration.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), told about a multicast group join
gnb2.cellularNic.rrc.registration.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe): a UE created during the run gets an IPv4 default route through the NIC only on an IP session, and the NIC of an Ethernet session is an Ethernet port; set by the NIC
gnb2.cellularNic.rrc.bearerManagement.binderModule	string	“binder”	To reach a peer’s BearerManagement on RLF
gnb2.cellularNic.rrc.bearerManagement.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), which a torn-down bearer’s DRB identity goes back through
gnb2.cellularNic.rrc.bearerManagement.t311	double	0s	RRC re-establishment cell-selection timer (0 => release-to-IDLE)
gnb2.cellularNic.rrc.bearerManagement.t301	double	0.1s	RRC re-establishment (request -> complete) timer
gnb2.cellularNic.rrc.bearerManagement.headerCompressedSize	int	-1B	Removed, an error if set: header compression is configured per bearer (the rohc field of BearerConfigurator’s bearer definitions)
gnb2.cellularNic.rrc.bearerManagement.pdcpEntityModuleType	string	“simu5g.stack.pdcp.LtePdcpEntity”	PDCP entity types: the full PDCP entity is a compound (PdcpEntityBase, TX+RX sides plus the leg split/join stage of a multi-leg bearer); the instantiable types are its subclasses (LtePdcpEntity, NrPdcpEntity). At a DC secondary a bearer’s PDCP lives at the master, so the secondary installs an PdcpRelayEntity (tunnels PDUs to/from the master) in its place.
gnb2.cellularNic.rrc.bearerManagement.pdcpRelayEntityModuleType	string	“simu5g.stack.pdcp.PdcpRelayEntity”
gnb2.cellularNic.rrc.bearerManagement.dualConnectivityEnabled	bool	false	Set by the NIC; two-leg (split-capable) bearers
gnb2.cellularNic.rrc.bearerManagement.rlcTmEntityModuleType	string	“simu5g.stack.rlc.RlcTmEntity”	RLC entity types (compound modules): lteRlc* = LTE-FI bearers (TS 36.322), nrRlc* = NR bearers (SI/SO wire format, TS 38.322)
gnb2.cellularNic.rrc.bearerManagement.lteRlcUmEntityModuleType	string	“simu5g.stack.rlc.LteRlcUmEntity”
gnb2.cellularNic.rrc.bearerManagement.lteRlcAmEntityModuleType	string	“simu5g.stack.rlc.LteRlcAmEntity”
gnb2.cellularNic.rrc.bearerManagement.nrRlcUmEntityModuleType	string	“simu5g.stack.rlc.NrRlcUmEntity”
gnb2.cellularNic.rrc.bearerManagement.nrRlcAmEntityModuleType	string	“simu5g.stack.rlc.NrRlcAmEntity”
gnb2.cellularNic.rrc.bearerManagement.registrationModule	string	“^.registration”	Module references for accessing other stack layers
gnb2.cellularNic.rrc.bearerManagement.drbTableModule	string	“^.drbTable”
gnb2.cellularNic.rrc.bearerManagement.ip2nicModule	string	“^.^.ip2nic”
gnb2.cellularNic.rrc.bearerManagement.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”	Attachment-ledger push target (UE only)
gnb2.cellularNic.rrc.bearerManagement.pdcpMuxModule	string	“^.^.pdcpMux”
gnb2.cellularNic.rrc.bearerManagement.pdcpDcMuxModule	string	“^.^.pdcpDcMux”
gnb2.cellularNic.rrc.bearerManagement.d2dModeControllerModule	string	“^.d2dModeController”
gnb2.cellularNic.rrc.bearerManagement.rlcMuxModule	string	“^.^.rlcMux”
gnb2.cellularNic.rrc.bearerManagement.nrRlcMuxModule	string	“^.^.nrRlcMux”
gnb2.cellularNic.rrc.bearerManagement.macModule	string	“^.^.mac”
gnb2.cellularNic.rrc.bearerManagement.nrMacModule	string	“^.^.nrMac”
gnb2.cellularNic.rrc.bearerManagement.sdapModule	string	“^.^.sdap”	Configuration push target; unresolvable (no SDAP on the NIC) = no pushes
gnb2.cellularNic.rrc.bearerManagement.qosFlowClassifierModule	string	“^.^.qosFlowClassifier”	Uplink QFI rule push target; unresolvable (not a UE stack with SDAP) = no pushes
gnb2.cellularNic.rrc.connectionControl.binderModule	string	“binder”
gnb2.cellularNic.rrc.connectionControl.bearerConfiguratorModule	string	“bearerConfigurator”
gnb2.cellularNic.rrc.connectionControl.coreControlModule	string	“coreControl”
gnb2.cellularNic.rrc.connectionControl.bearerManagementModule	string	“^.bearerManagement”
gnb2.cellularNic.rrc.connectionControl.macModule	string	“^.^.mac”
gnb2.cellularNic.rrc.connectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
gnb2.cellularNic.rrc.connectionControl.gtpUserModule	string	“^.^.^.relay.gtpUser”
gnb2.cellularNic.rrc.connectionControl.gtpUserX2Module	string	“^.^.^.gtpUserX2”
gnb2.cellularNic.rrc.connectionControl.macNodeId	int		The base station’s node id; the NIC sets it from the node’s
gnb2.cellularNic.rrc.connectionControl.gateway	string	“”	The node’s core network gateway, as its gateway parameter names it; ignored at a node not connected to a core network (a secondary node)
gnb2.cellularNic.rrc.nrConnectionControl.dynamicCellAssociation	bool	false
gnb2.cellularNic.rrc.nrConnectionControl.enableHandover	bool	false	Allows handovers in the UE
gnb2.cellularNic.rrc.nrConnectionControl.isNr	bool		Whether this instance is associated with the NR or the LTE stack
gnb2.cellularNic.rrc.nrConnectionControl.macNodeId	int		MacNodeId of the stack leg this controller belongs to (set by the NIC)
gnb2.cellularNic.rrc.nrConnectionControl.sessionType	string		The type of the session the UE requests at connection setup (see LteUe), set by the NIC
gnb2.cellularNic.rrc.nrConnectionControl.handoverLatency	double	50ms	Handover duration
gnb2.cellularNic.rrc.nrConnectionControl.handoverDetachmentTime	double	handoverLatency > 0s ? handoverLatency/2 : 25ms
gnb2.cellularNic.rrc.nrConnectionControl.handoverAttachmentTime	double	handoverLatency > 0s ? handoverLatency-handoverDetachmentTime : handoverDetachmentTime
gnb2.cellularNic.rrc.nrConnectionControl.minRssiDefault	bool	true	Whether minRssi is taken from PhyPisaData instead of the minRssi parameter
gnb2.cellularNic.rrc.nrConnectionControl.minRssi	double	-99.0dB	Configurable minimum threshold RSSI for attaching to an eNB (meaningful only if minRssiDefault==false)
gnb2.cellularNic.rrc.nrConnectionControl.hysteresisFactor	double	10
gnb2.cellularNic.rrc.nrConnectionControl.binderModule	string	“binder”
gnb2.cellularNic.rrc.nrConnectionControl.macModule	string	“^.^.mac”
gnb2.cellularNic.rrc.nrConnectionControl.bearerManagementModule	string	“^.bearerManagement”
gnb2.cellularNic.rrc.nrConnectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
gnb2.cellularNic.rrc.nrConnectionControl.feedbackGeneratorModule	string	“^.^.dlFbGen”	TODO or “^.^.nrDlFbGen”
gnb2.cellularNic.rrc.nrConnectionControl.otherConnectionControlModule	string	“”
gnb2.cellularNic.rrc.nrConnectionControl.hasCollector	bool	false	True when node has a collector module (ueCollector/nrUeCollector) for this PHY module
gnb2.cellularNic.rrc.d2dModeSelection.modeSelectionPeriod	double	1s
gnb2.cellularNic.rrc.d2dModeSelection.binderModule	string	“binder”
gnb2.cellularNic.rrc.d2dModeSelection.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
gnb2.cellularNic.rrc.d2dModeSelection.macModule	string	“^.^.mac”
gnb2.cellularNic.rrc.d2dModeSelection.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point, which knows the UEs handing over
gnb2.cellularNic.rlcMux.bearerManagementModule	string	“^.rrc.bearerManagement”
gnb2.cellularNic.phy.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb on their PHY submodule)
gnb2.cellularNic.phy.macNodeId	int		MacNodeId of the stack leg this PHY belongs to (set by the NIC)
gnb2.cellularNic.phy.ueTxPower	double	26dBm
gnb2.cellularNic.phy.eNodeBTxPower	double	46dBm
gnb2.cellularNic.phy.microTxPower	double	30dBm
gnb2.cellularNic.phy.txDirection	string	“OMNI”
gnb2.cellularNic.phy.txAngle	double	0deg
gnb2.cellularNic.phy.binderModule	string	“binder”
gnb2.cellularNic.phy.channelModelModule	string	“^.channelModel[0]”	Set to “^.nrChannelModel[0]” on an NR leg, see NrNicUe
gnb2.cellularNic.phy.enableHandover	bool	false	Marks this eNB as a handover target: its beacons are used by UEs for handover feasibility assessment. Requires enableBeacons=true (the default when handover is on); the module errors out at initialization if beacons are disabled while handover is enabled.
gnb2.cellularNic.phy.enableBeacons	bool	enableHandover	Enables broadcasting periodic beacons (at cellInfo.beaconInterval). Beacons are the measurement signal UEs use both for handover feasibility assessment and for radio link monitoring (RLF detection), decoupled from enableHandover so radio link monitoring can run without handover. Defaults to enableHandover (beacons flow exactly when handover is enabled). cellInfo.beaconInterval must be positive: a zero/negative interval is an error – switch beacons off with enableBeacons=false.
gnb2.cellularNic.phy.targetBler	double	0.001
gnb2.cellularNic.packetFlowObserver.macModule	string	“^.mac”
gnb2.cellularNic.packetFlowObserver.pdcpModule	string	“^”
gnb2.cellularNic.packetFlowObserver.rlcModule	string	“^”
gnb2.cellularNic.packetFlowObserver.isNrObserver	bool	false
gnb2.cellularNic.packetFlowObserver.pfmType	string	“PacketFlowObserverEnb”
gnb2.cellularNic.pdcpDcMux.bearerManagementModule	string	“^.rrc.bearerManagement”
gnb2.cellularNic.x2Manager.interfaceTableModule	string
gnb2.cellularNic.x2Manager.binderModule	string	“binder”
gnb2.cellularNic.compManager.compNodeType	string	“COMP_CLIENT”
gnb2.cellularNic.compManager.coordinatorId	int		ID of the coordinator node
gnb2.cellularNic.compManager.clientList	object	[]	Space-separated list of client node identifiers
gnb2.cellularNic.compManager.coordinationPeriod	double	0.001s	The time interval between two coordination events
gnb2.cellularNic.compManager.binderModule	string	“binder”
gnb2.cellularNic.handoverX2Forwarder.losslessHandover	bool	false
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialLatitude	double	nan deg
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialLongitude	double	nan deg
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialAltitude	double	0m
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialHeading	double	0deg
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialElevation	double	0deg
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initialBank	double	0deg
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
gnb2.cellularNic.bgTrafficGenerator.bgUE.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.computeAvgInterference	bool
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.enablePeriodicCqiUpdate	bool
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.useProbabilisticCqi	bool
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.backgroundTrafficManagerModule	string	“^.^.manager”
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.startTimeDl	double	-1s
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.startTimeUl	double	-1s
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.headerLen	int	33B
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.txPower	double	26dBm
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.fbPeriod	int	6tti
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.periodDl	double	uniform(10ms,50ms)
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.periodUl	double	uniform(10ms,50ms)
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.packetSizeDl	int	intuniform(20B,100B)
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.packetSizeUl	int	intuniform(20B,100B)
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.rtxRateDl	double	0.1
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.rtxDelayDl	double	0.006s
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.rtxRateUl	double	0.1
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.rtxDelayUl	double	0.006s
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.cqiMeanDl	double	15	These values are only considered when periodicCqi == false && computeAvgInterference == false
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.cqiMeanUl	double	15
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.cqiStddevDl	double	0
gnb2.cellularNic.bgTrafficGenerator.bgUE.generator.cqiStddevUl	double	0
gnb2.cellularNic.bgTrafficGenerator.manager.binderModule	string	“binder”
gnb2.cellularNic.bgTrafficGenerator.manager.numBgUes	int
gnb2.cellularNic.bgTrafficGenerator.manager.macModule	string	“^.^.mac”
gnb2.cellularNic.bgTrafficGenerator.manager.phyModule	string	“^.^.phy”
gnb2.cellularNic.bgTrafficGenerator.manager.enablePeriodicCqiUpdate	bool
gnb2.cellularNic.bgTrafficGenerator.manager.computeAvgInterference	bool
gnb2.pppIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb2.pppIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb2.pppIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb2.pppIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb2.pppIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb2.pppIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb2.pppIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb2.pppIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb2.pppIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb2.pppIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb2.pppIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb2.pppIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb2.pppIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb2.pppIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb2.pppIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb2.pppIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb2.pppIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb2.pppIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb2.pppIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb2.pppIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.pppIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb2.pppIf ↗.ppp ↗.mtu	int	4470B
gnb2.pppIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb2.pppIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb2.x2ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.x2ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb2.x2ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb2.x2ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb2.x2ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb2.x2ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb2.x2ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb2.x2ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb2.x2ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb2.x2ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb2.x2ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb2.x2ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb2.x2ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb2.x2ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb2.x2ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb2.x2ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.x2ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb2.x2ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb2.x2ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb2.x2ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb2.x2ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb2.x2ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.x2ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.x2ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb2.x2ppp ↗.ppp ↗.mtu	int	4470B
gnb2.x2ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb2.x2ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb2.pppMEHostIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppMEHostIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
gnb2.pppMEHostIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
gnb2.pppMEHostIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
gnb2.pppMEHostIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
gnb2.pppMEHostIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
gnb2.pppMEHostIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
gnb2.pppMEHostIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
gnb2.pppMEHostIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
gnb2.pppMEHostIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
gnb2.pppMEHostIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
gnb2.pppMEHostIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
gnb2.pppMEHostIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
gnb2.pppMEHostIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
gnb2.pppMEHostIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
gnb2.pppMEHostIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppMEHostIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
gnb2.pppMEHostIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
gnb2.pppMEHostIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
gnb2.pppMEHostIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
gnb2.pppMEHostIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
gnb2.pppMEHostIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.pppMEHostIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.pppMEHostIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
gnb2.pppMEHostIf ↗.ppp ↗.mtu	int	4470B
gnb2.pppMEHostIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
gnb2.pppMEHostIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb2.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.configurator ↗.routingTableModule	string
gnb2.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
gnb2.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
gnb2.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
gnb2.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
gnb2.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
gnb2.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
gnb2.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
gnb2.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
gnb2.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
gnb2.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
gnb2.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
gnb2.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
gnb2.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.igmp ↗.routingTableModule	string
gnb2.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
gnb2.ipv4 ↗.igmp ↗.enabled	bool	true
gnb2.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
gnb2.ipv4 ↗.igmp ↗.queryInterval	double	125s
gnb2.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
gnb2.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
gnb2.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
gnb2.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
gnb2.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
gnb2.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
gnb2.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
gnb2.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
gnb2.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.icmp ↗.routingTableModule	string
gnb2.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
gnb2.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
gnb2.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
gnb2.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
gnb2.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.ip ↗.routingTableModule	string
gnb2.ipv4 ↗.ip ↗.arpModule	string
gnb2.ipv4 ↗.ip ↗.icmpModule	string
gnb2.ipv4 ↗.ip ↗.checksumMode	string	“declared”
gnb2.ipv4 ↗.ip ↗.timeToLive	int	32
gnb2.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
gnb2.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
gnb2.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
gnb2.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
gnb2.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
gnb2.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
gnb2.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
gnb2.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv4 ↗.arp ↗.routingTableModule	string
gnb2.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
gnb2.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
gnb2.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
gnb2.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
gnb2.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
gnb2.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
gnb2.ipv4 ↗.ipsec ↗.interfaceTableModule	string
gnb2.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
gnb2.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
gnb2.ipv4 ↗.ipsec ↗.spdConfig	xml
gnb2.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
gnb2.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
gnb2.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
gnb2.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
gnb2.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
gnb2.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
gnb2.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
gnb2.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
gnb2.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
gnb2.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
gnb2.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
gnb2.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.configurator ↗.interfaceTableModule	string
gnb2.ipv6 ↗.configurator ↗.routingTableModule	string
gnb2.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
gnb2.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
gnb2.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
gnb2.ipv6 ↗.routingTable ↗.forwarding	bool	false
gnb2.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
gnb2.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
gnb2.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
gnb2.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
gnb2.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
gnb2.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
gnb2.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
gnb2.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
gnb2.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
gnb2.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
gnb2.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
gnb2.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
gnb2.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
gnb2.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
gnb2.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
gnb2.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
gnb2.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
gnb2.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
gnb2.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
gnb2.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
gnb2.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
gnb2.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
gnb2.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
gnb2.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
gnb2.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
gnb2.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
gnb2.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
gnb2.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
gnb2.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv6 ↗.ipv6 ↗.routingTableModule	string
gnb2.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
gnb2.ipv6 ↗.ipv6 ↗.icmpv6Module	string
gnb2.ipv6 ↗.ipv6 ↗.procDelay	double	0s
gnb2.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
gnb2.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.ipsec ↗.interfaceTableModule	string
gnb2.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
gnb2.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
gnb2.ipv6 ↗.ipsec ↗.spdConfig	xml
gnb2.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
gnb2.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
gnb2.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
gnb2.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
gnb2.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
gnb2.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
gnb2.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
gnb2.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
gnb2.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
gnb2.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
gnb2.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
gnb2.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
gnb2.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
gnb2.ipv6 ↗.mipv6 ↗.isMobileNode	bool
gnb2.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
gnb2.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
gnb2.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
gnb2.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
gnb2.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
gnb2.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
gnb2.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
gnb2.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
gnb2.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
gnb2.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
gnb2.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
gnb2.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
gnb2.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
gnb2.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
gnb2.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
gnb2.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
gnb2.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
gnb2.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
gnb2.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
gnb2.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
gnb2.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
gnb2.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
gnb2.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
gnb2.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
gnb2.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
gnb2.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
gnb2.udp ↗.checksumMode	string	“declared”
gnb2.udp ↗.defaultMulticastLoop	bool	true
gnb2.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.tcp ↗.checksumMode	string	“declared”
gnb2.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
gnb2.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
gnb2.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
gnb2.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
gnb2.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
gnb2.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
gnb2.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
gnb2.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
gnb2.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
gnb2.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
gnb2.tcp ↗.msl	int	120s	Maximum Segment Lifetime
gnb2.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
gnb2.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
gnb2.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
gnb2.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
gnb2.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
gnb2.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
gnb2.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
gnb2.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
gnb2.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
gnb2.x2App.client.displayStringTextFormat	string	“{socketState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.x2App.client.localAddress	string	“”	Comma-separated list of addresses
gnb2.x2App.client.localPort	int	0	Port number to listen on
gnb2.x2App.client.connectAddress	string		Server address (may be symbolic)
gnb2.x2App.client.connectPort	int	5000	Port number to connect to
gnb2.x2App.client.startTime	double	0s	Time the first session begins
gnb2.x2App.client.numRequestsPerSession	int	1	Number of requests sent per session
gnb2.x2App.client.numPacketsToReceive	int	0
gnb2.x2App.client.requestLength	int	1452	Length of a request (bytes)
gnb2.x2App.client.thinkTime	double	0s	Time gap between requests
gnb2.x2App.client.waitToClose	double	0s	Time to wait between the last message sent and abort
gnb2.x2App.client.reconnectInterval	double	0s	If the connection breaks, waits this much before trying to reconnect
gnb2.x2App.client.inboundStreams	int	17
gnb2.x2App.client.outboundStreams	int	1
gnb2.x2App.client.echo	bool	false	Echoes received packages when true
gnb2.x2App.client.ordered	bool	true
gnb2.x2App.client.queueSize	int	0
gnb2.x2App.client.prMethod	int	0	0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST
gnb2.x2App.client.prValue	double	0	For PR-SCTP
gnb2.x2App.client.streamReset	bool	false
gnb2.x2App.client.streamRequestTime	double	0s
gnb2.x2App.client.streamResetType	int	5	NO_RESET=5, RESET_OUTGOING=6, RESET_INCOMING=7, RESET_BOTH=8, SSN_TSN=9
gnb2.x2App.client.streamToReset	int	0
gnb2.x2App.client.stopTime	double	-1s	Time of finishing sending, negative values mean forever
gnb2.x2App.client.primaryTime	double	0s
gnb2.x2App.client.newPrimary	string	“”
gnb2.x2App.client.streamRequestLengths	string	“”
gnb2.x2App.client.streamRequestRatio	string	“”
gnb2.x2App.client.streamPriorities	string	“”
gnb2.x2App.client.finishEndsSimulation	bool	false
gnb2.x2App.client.binderModule	string	“binder”
gnb2.x2App.server.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.x2App.server.localAddress	string	“”	Comma-separated list of addresses
gnb2.x2App.server.localPort	int	0	Port number to listen on
gnb2.x2App.server.echo	bool	false	Echoes received packages when true
gnb2.x2App.server.echoDelay	double	0s
gnb2.x2App.server.delayFirstRead	double	0s
gnb2.x2App.server.readingInterval	double	0s
gnb2.x2App.server.messagesToPush	int	0
gnb2.x2App.server.numPacketsToSendPerClient	int	0	Number of requests sent per session
gnb2.x2App.server.numPacketsToReceivePerClient	int	1
gnb2.x2App.server.requestLength	int	1452	Length of a request (bytes)
gnb2.x2App.server.thinkTime	double	0s	Time gap between requests
gnb2.x2App.server.waitToClose	double	0s	Time to wait between last message sent and abort
gnb2.x2App.server.finishEndsSimulation	bool	false
gnb2.x2App.server.ordered	bool	true
gnb2.x2App.server.inboundStreams	int	17
gnb2.x2App.server.outboundStreams	int	1
gnb2.x2App.server.queueSize	int	0
gnb2.x2App.server.prMethod	int	0	0=NONE, 1=PR_TTL, 2=PR_RTX, 3=PR_PRIO, 4=PR_STRRST
gnb2.x2App.server.prValue	double	0	For PR-SCTP
gnb2.x2App.server.streamReset	bool	false
gnb2.x2App.server.streamRequestTime	double	0s
gnb2.x2App.server.streamToReset	int	0
gnb2.x2App.server.streamPriorities	string	“”
gnb2.x2App.server.binderModule	string	“binder”
gnb2.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.sctp ↗.interfaceTableModule	string
gnb2.sctp ↗.routingTableModule	string
gnb2.sctp ↗.checksumMode	string	“declared”
gnb2.sctp ↗.numGapReports	int	3
gnb2.sctp ↗.rtoInitial	double	3s
gnb2.sctp ↗.rtoMin	double	1s
gnb2.sctp ↗.rtoMax	double	60s
gnb2.sctp ↗.rtoAlpha	double	0.125
gnb2.sctp ↗.rtoBeta	double	0.250
gnb2.sctp ↗.maxBurst	int	4
gnb2.sctp ↗.maxBurstVariant	string	“maxBurst”
gnb2.sctp ↗.initialWindow	int	0
gnb2.sctp ↗.assocMaxRetrans	int	10
gnb2.sctp ↗.pathMaxRetrans	int	5
gnb2.sctp ↗.maxInitRetrans	int	8
gnb2.sctp ↗.sackPeriod	double	200ms
gnb2.sctp ↗.sackFrequency	int	2
gnb2.sctp ↗.reactivatePrimaryPath	bool	false
gnb2.sctp ↗.sendQueueLimit	int	0
gnb2.sctp ↗.validCookieLifetime	double	10s
gnb2.sctp ↗.enableHeartbeats	bool	true
gnb2.sctp ↗.hbInterval	double	30s
gnb2.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
gnb2.sctp ↗.nagleEnabled	bool	true
gnb2.sctp ↗.naglePoint	int	1468
gnb2.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
gnb2.sctp ↗.fastRecoverySupported	bool	true
gnb2.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
gnb2.sctp ↗.ccModule	int	0	RFC4960=0
gnb2.sctp ↗.osbWithHeader	bool	false
gnb2.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
gnb2.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
gnb2.sctp ↗.arwnd	int	65535
gnb2.sctp ↗.swsLimit	int	3000	Limit for SWS
gnb2.sctp ↗.udpEncapsEnabled	bool	false
gnb2.sctp ↗.natFriendly	bool	false
gnb2.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
gnb2.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
gnb2.sctp ↗.tellArwnd	bool	false	For flow control
gnb2.sctp ↗.messageAcceptLimit	int	0	For flow control
gnb2.sctp ↗.fairStart	double	0s
gnb2.sctp ↗.fairStop	double	0s
gnb2.sctp ↗.streamsToPaths	string	“”
gnb2.sctp ↗.startEndToEndDelay	int	0
gnb2.sctp ↗.stopEndToEndDelay	int	10
gnb2.sctp ↗.throughputInterval	double	1
gnb2.sctp ↗.auth	bool	false
gnb2.sctp ↗.chunks	string	“”
gnb2.sctp ↗.padding	bool	false
gnb2.sctp ↗.addIP	bool	false
gnb2.sctp ↗.addTime	double	0s
gnb2.sctp ↗.addAddress	string	“”
gnb2.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
gnb2.sctp ↗.packetDrop	bool	false
gnb2.sctp ↗.sackNow	bool	false
gnb2.sctp ↗.highSpeedCC	bool	false
gnb2.sctp ↗.checkSackSeqNumber	bool	false
gnb2.sctp ↗.nrSack	bool	false
gnb2.sctp ↗.disableReneging	bool	false
gnb2.sctp ↗.gapReportLimit	int	100000000
gnb2.sctp ↗.gapListOptimizationVariant	string	“none”
gnb2.sctp ↗.smartOverfullSACKHandling	bool	false
gnb2.sctp ↗.allowQoSTracking	bool	false
gnb2.sctp ↗.qosTrackingInterval	double	1.0s
gnb2.sctp ↗.cmtSendAllVariant	string	“normal”
gnb2.sctp ↗.cmtRetransmissionVariant	string	“normal”
gnb2.sctp ↗.cmtCUCVariant	string	“normal”
gnb2.sctp ↗.cmtBufferSplitVariant	string	“none”
gnb2.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
gnb2.sctp ↗.cmtUseSFR	bool	true
gnb2.sctp ↗.cmtUseDAC	bool	true
gnb2.sctp ↗.cmtUseFRC	bool	true
gnb2.sctp ↗.cmtSmartT3Reset	bool	true
gnb2.sctp ↗.cmtSmartFastRTX	bool	true
gnb2.sctp ↗.cmtSmartReneging	bool	false
gnb2.sctp ↗.cmtSlowPathRTTUpdate	bool	false
gnb2.sctp ↗.cmtChunkReschedulingVariant	string	“none”
gnb2.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
gnb2.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
gnb2.sctp ↗.movedChunkFastRTXFactor	double	2.0
gnb2.sctp ↗.cmtSackPath	string	“standard”
gnb2.sctp ↗.strictCwndBooking	bool	false
gnb2.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
gnb2.sctp ↗.cmtCCPathGroups	string	“”
gnb2.sctp ↗.rpPathBlocking	bool	false
gnb2.sctp ↗.rpScaleBlockingTimeout	bool	false
gnb2.sctp ↗.rpMinCwnd	int	1
gnb2.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.at ↗.forwardServiceRegistration	bool	true
gnb2.at ↗.forwardProtocolRegistration	bool	true
gnb2.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.tn ↗.forwardServiceRegistration	bool	true
gnb2.tn ↗.forwardProtocolRegistration	bool	true
gnb2.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
gnb2.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
gnb2.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
gnb2.nl ↗.forwardServiceRegistration	bool	true
gnb2.nl ↗.forwardProtocolRegistration	bool	true
gnb2.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
gnb2.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
gnb2.relay.trafficFlowFilter.binderModule	string	“binder”
gnb2.relay.trafficFlowFilter.fastForwarding	bool	true
gnb2.relay.gtpUser.binderModule	string	“binder”
gnb2.relay.gtpUser.localPort	int	31
gnb2.relay.gtpUser.tunnelPeerPort	int	31
gnb2.gtpUserX2.binderModule	string	“binder”
gnb2.gtpUserX2.localPort	int	32
gnb2.gtpUserX2.tunnelPeerPort	int	32
bgCell.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
bgCell.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
bgCell.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
bgCell.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
bgCell.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
bgCell.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
bgCell.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
bgCell.mobility ↗.initialLatitude	double	nan deg
bgCell.mobility ↗.initialLongitude	double	nan deg
bgCell.mobility ↗.initialAltitude	double	0m
bgCell.mobility ↗.initialHeading	double	0deg
bgCell.mobility ↗.initialElevation	double	0deg
bgCell.mobility ↗.initialBank	double	0deg
bgCell.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
bgCell.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
bgCell.bgChannelModel.binderModule	string	“binder”	Module references
bgCell.bgChannelModel.shadowing	bool	true	Enable/disable shadowing
bgCell.bgChannelModel.scenario	string	“URBAN_MACROCELL”	Path loss scenario, in ITU terminology
bgCell.bgChannelModel.nodebHeight	double	25m	eNodeB height
bgCell.bgChannelModel.buildingHeight	double	20m	Building height
bgCell.bgChannelModel.insideBuilding	bool	false	Determines if the UE is inside a building
bgCell.bgChannelModel.streetWidth	double	20m	TODO width
bgCell.bgChannelModel.ueHeight	double	1.5m
bgCell.bgChannelModel.tolerateMaxDistViolation	bool	false
bgCell.bgChannelModel.correlationDistance	double	50m
bgCell.bgChannelModel.antennaGainUe	double	0dBi	Antenna gain of the UE, relative to an isotropic antenna
bgCell.bgChannelModel.antennGainEnB	double	18dBi	Antenna gain of the eNodeB
bgCell.bgChannelModel.antennGainMicro	double	5dBi	Antenna gain of the micro node
bgCell.bgChannelModel.thermalNoise	double	-104.5dBm	Thermal noise for 10 MHz of bandwidth
bgCell.bgChannelModel.ueNoiseFigure	double	7dBm	UE noise figure
bgCell.bgChannelModel.bsNoiseFigure	double	5dBm	eNodeB noise figure
bgCell.bgChannelModel.cableLoss	double	2dB	Cable loss
bgCell.bgChannelModel.dynamicLos	bool	false	Whether LOS/NLOS is drawn per link from the scenario’s LOS probability; when false, it is fixed to fixedLos
bgCell.bgChannelModel.fixedLos	bool	false	LOS state of every link when dynamicLos is false: true = LOS, false = NLOS
bgCell.bgChannelModel.fading	bool	true	Enable/disable fading
bgCell.bgChannelModel.fadingType	string	“JAKES”	Fading type (JAKES or RAYLEIGH)
bgCell.bgChannelModel.numFadingPaths	int	6	If Jakes fading, this parameter specifies the number of paths (tap channel)
bgCell.bgChannelModel.delayRms	double	363ns
bgCell.bgChannelModel.bgCellInterference	bool	true	Whether interference from the other background cells is included in the SINR, in both UL and DL
bgCell.bgChannelModel.downlinkInterference	bool	true	Whether interference from other base stations is included in the DL SINR
bgCell.bgChannelModel.uplinkInterference	bool	true	Whether interference from the UEs of other cells is included in the UL SINR
bgCell.bgScheduler.binderModule	string	“binder”
bgCell.bgScheduler.channelModelModule	string	“^.bgChannelModel”
bgCell.bgScheduler.txPower	double	46dBm	Transmission power
bgCell.bgScheduler.txDirection	string	“OMNI”	Transmission direction
bgCell.bgScheduler.txAngle	double	0deg	Transmission angle
bgCell.bgScheduler.isNr	bool	false	Flag to indicate whether this is a NR base station
bgCell.bgScheduler.numerologyIndex	int	0	Operating carrier
bgCell.bgScheduler.carrierFrequency	double	2GHz	Operating carrier
bgCell.bgScheduler.numBands	int	6	Carrier bandwidth
bgCell.bgTrafficGenerator.bgUE.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
bgCell.bgTrafficGenerator.bgUE.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
bgCell.bgTrafficGenerator.bgUE.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialLatitude	double	nan deg
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialLongitude	double	nan deg
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialAltitude	double	0m
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialHeading	double	0deg
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialElevation	double	0deg
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initialBank	double	0deg
bgCell.bgTrafficGenerator.bgUE.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
bgCell.bgTrafficGenerator.bgUE.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
bgCell.bgTrafficGenerator.bgUE.generator.computeAvgInterference	bool
bgCell.bgTrafficGenerator.bgUE.generator.enablePeriodicCqiUpdate	bool
bgCell.bgTrafficGenerator.bgUE.generator.useProbabilisticCqi	bool
bgCell.bgTrafficGenerator.bgUE.generator.backgroundTrafficManagerModule	string	“^.^.manager”
bgCell.bgTrafficGenerator.bgUE.generator.startTimeDl	double	-1s
bgCell.bgTrafficGenerator.bgUE.generator.startTimeUl	double	-1s
bgCell.bgTrafficGenerator.bgUE.generator.headerLen	int	33B
bgCell.bgTrafficGenerator.bgUE.generator.txPower	double	26dBm
bgCell.bgTrafficGenerator.bgUE.generator.fbPeriod	int	6tti
bgCell.bgTrafficGenerator.bgUE.generator.periodDl	double	uniform(10ms,50ms)
bgCell.bgTrafficGenerator.bgUE.generator.periodUl	double	uniform(10ms,50ms)
bgCell.bgTrafficGenerator.bgUE.generator.packetSizeDl	int	intuniform(20B,100B)
bgCell.bgTrafficGenerator.bgUE.generator.packetSizeUl	int	intuniform(20B,100B)
bgCell.bgTrafficGenerator.bgUE.generator.rtxRateDl	double	0.1
bgCell.bgTrafficGenerator.bgUE.generator.rtxDelayDl	double	0.006s
bgCell.bgTrafficGenerator.bgUE.generator.rtxRateUl	double	0.1
bgCell.bgTrafficGenerator.bgUE.generator.rtxDelayUl	double	0.006s
bgCell.bgTrafficGenerator.bgUE.generator.cqiMeanDl	double	15	These values are only considered when periodicCqi == false && computeAvgInterference == false
bgCell.bgTrafficGenerator.bgUE.generator.cqiMeanUl	double	15
bgCell.bgTrafficGenerator.bgUE.generator.cqiStddevDl	double	0
bgCell.bgTrafficGenerator.bgUE.generator.cqiStddevUl	double	0
bgCell.bgTrafficGenerator.manager.binderModule	string	“binder”
bgCell.bgTrafficGenerator.manager.numBgUes	int
bgCell.bgTrafficGenerator.manager.macModule	string	“^.^.mac”
bgCell.bgTrafficGenerator.manager.phyModule	string	“^.^.phy”
bgCell.bgTrafficGenerator.manager.enablePeriodicCqiUpdate	bool
bgCell.bgTrafficGenerator.manager.computeAvgInterference	bool
ue.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.status ↗.initialStatus	string	“UP”	Initial status of the network node
ue.mobility ↗.displayStringTextFormat	string	“p: {position}\nv: {velocity}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.mobility ↗.subjectModule	string	“^”	The module path that determines the subject module, the motion of which this mobility model describes. The default value is the parent module
ue.mobility ↗.coordinateSystemModule	string	“”	The module path of the geographic coordinate system module; optional, empty disables geographic conversion (and the {geo_position} directive)
ue.mobility ↗.updateDisplayString	bool	true	Enables continuous update of the subject module’s position by modifying its display string
ue.mobility ↗.constraintAreaMinX	double	-inf m	The minimum x position of the constraint area. It is unconstrained by default (negative infinity)
ue.mobility ↗.constraintAreaMinY	double	-inf m	The minimum y position of the constraint area. It is unconstrained by default (negative infinity)
ue.mobility ↗.constraintAreaMinZ	double	-inf m	The minimum z position of the constraint area. It is unconstrained by default (negative infinity)
ue.mobility ↗.constraintAreaMaxX	double	inf m	The maximum x position of the constraint area. It is unconstrained by default (positive infinity)
ue.mobility ↗.constraintAreaMaxY	double	inf m	The maximum y position of the constraint area. It is unconstrained by default (positive infinity)
ue.mobility ↗.constraintAreaMaxZ	double	inf m	The maximum z position of the constraint area. It is unconstrained by default (positive infinity)
ue.mobility ↗.initialX	double	uniform(this.constraintAreaMinX, this.constraintAreaMaxX)
ue.mobility ↗.initialY	double	uniform(this.constraintAreaMinY, this.constraintAreaMaxY)
ue.mobility ↗.initialZ	double	nanToZero(uniform(this.constraintAreaMinZ, this.constraintAreaMaxZ))
ue.mobility ↗.initialLatitude	double	nan deg
ue.mobility ↗.initialLongitude	double	nan deg
ue.mobility ↗.initialAltitude	double	0m
ue.mobility ↗.initialHeading	double	0deg
ue.mobility ↗.initialElevation	double	0deg
ue.mobility ↗.initialBank	double	0deg
ue.mobility ↗.initFromDisplayString	bool	true	Enables one-time initialization from the subject module’s display string
ue.mobility ↗.updateFromDisplayString	bool	true	Enables continuous update from the subject module’s display string for dragging and rotating it
ue.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.environment ↗.initStage	int	0	Initialization stage for the setup command
ue.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
ue.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
ue.environment ↗.setupCommand	string	“”	A host OS system command
ue.environment ↗.teardownCommand	string	“”	A host OS system command
ue.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
ue.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
ue.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.cb ↗.forwardServiceRegistration	bool	true
ue.cb ↗.forwardProtocolRegistration	bool	true
ue.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.bl ↗.forwardServiceRegistration	bool	true
ue.bl ↗.forwardProtocolRegistration	bool	true
ue.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
ue.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ethernet ↗.fcsMode	string	“declared”
ue.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
ue.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
ue.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.li ↗.forwardServiceRegistration	bool	true
ue.li ↗.forwardProtocolRegistration	bool	true
ue.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.lo ↗.lo ↗.mtu	int	4470B
ue.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.wlan ↗.agent ↗.mibModule	string
ue.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
ue.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
ue.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
ue.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
ue.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
ue.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
ue.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
ue.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
ue.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
ue.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
ue.wlan ↗.mgmt ↗.mibModule	string
ue.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
ue.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
ue.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
ue.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
ue.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
ue.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
ue.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
ue.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
ue.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
ue.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
ue.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
ue.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
ue.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
ue.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
ue.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
ue.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
ue.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
ue.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
ue.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
ue.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
ue.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
ue.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
ue.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
ue.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
ue.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
ue.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
ue.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
ue.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.ds ↗.mibModule	string
ue.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.wlan ↗.mac ↗.tx ↗.rxModule	string
ue.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
ue.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
ue.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
ue.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
ue.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
ue.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
ue.ppp ↗.ppp ↗.mtu	int	4470B
ue.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
ue.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
ue.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.tun ↗.tun ↗.mtu	int	1500B
ue.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.virt ↗.tunnel ↗.interfaceTableModule	string
ue.virt ↗.tunnel ↗.realInterface	string
ue.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
ue.virt ↗.tunnel ↗.address	string	“copy”
ue.virt ↗.tunnel ↗.vlanId	int	-1
ue.virt ↗.tunnel ↗.steal	bool	vlanId != -1
ue.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.configurator ↗.routingTableModule	string
ue.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
ue.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
ue.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
ue.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
ue.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
ue.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
ue.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
ue.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
ue.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
ue.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
ue.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
ue.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
ue.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.igmp ↗.routingTableModule	string
ue.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
ue.ipv4 ↗.igmp ↗.enabled	bool	true
ue.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
ue.ipv4 ↗.igmp ↗.queryInterval	double	125s
ue.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
ue.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
ue.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
ue.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
ue.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
ue.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
ue.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
ue.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
ue.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.icmp ↗.routingTableModule	string
ue.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
ue.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
ue.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
ue.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
ue.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.ip ↗.routingTableModule	string
ue.ipv4 ↗.ip ↗.arpModule	string
ue.ipv4 ↗.ip ↗.icmpModule	string
ue.ipv4 ↗.ip ↗.checksumMode	string	“declared”
ue.ipv4 ↗.ip ↗.timeToLive	int	32
ue.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
ue.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
ue.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
ue.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
ue.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
ue.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
ue.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
ue.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv4 ↗.arp ↗.routingTableModule	string
ue.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
ue.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
ue.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
ue.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
ue.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
ue.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
ue.ipv4 ↗.ipsec ↗.interfaceTableModule	string
ue.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
ue.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
ue.ipv4 ↗.ipsec ↗.spdConfig	xml
ue.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
ue.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
ue.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
ue.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
ue.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
ue.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
ue.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
ue.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
ue.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
ue.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
ue.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
ue.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.configurator ↗.interfaceTableModule	string
ue.ipv6 ↗.configurator ↗.routingTableModule	string
ue.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
ue.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
ue.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
ue.ipv6 ↗.routingTable ↗.forwarding	bool	false
ue.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
ue.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
ue.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
ue.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
ue.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
ue.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
ue.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
ue.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
ue.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
ue.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
ue.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
ue.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
ue.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
ue.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
ue.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
ue.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
ue.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
ue.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
ue.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
ue.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
ue.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
ue.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
ue.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
ue.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
ue.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
ue.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
ue.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
ue.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
ue.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv6 ↗.ipv6 ↗.routingTableModule	string
ue.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
ue.ipv6 ↗.ipv6 ↗.icmpv6Module	string
ue.ipv6 ↗.ipv6 ↗.procDelay	double	0s
ue.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
ue.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.ipsec ↗.interfaceTableModule	string
ue.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
ue.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
ue.ipv6 ↗.ipsec ↗.spdConfig	xml
ue.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
ue.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
ue.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
ue.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
ue.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
ue.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
ue.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
ue.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
ue.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
ue.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
ue.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
ue.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
ue.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
ue.ipv6 ↗.mipv6 ↗.isMobileNode	bool
ue.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
ue.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
ue.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
ue.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
ue.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
ue.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
ue.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
ue.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
ue.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
ue.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
ue.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
ue.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
ue.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
ue.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
ue.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
ue.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
ue.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
ue.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
ue.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
ue.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
ue.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
ue.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
ue.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
ue.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
ue.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
ue.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.nl ↗.forwardServiceRegistration	bool	true
ue.nl ↗.forwardProtocolRegistration	bool	true
ue.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ue.udp ↗.checksumMode	string	“declared”
ue.udp ↗.defaultMulticastLoop	bool	true
ue.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.tcp ↗.checksumMode	string	“declared”
ue.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
ue.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
ue.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
ue.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
ue.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
ue.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
ue.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
ue.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
ue.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
ue.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
ue.tcp ↗.msl	int	120s	Maximum Segment Lifetime
ue.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
ue.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
ue.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
ue.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
ue.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
ue.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
ue.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
ue.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
ue.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
ue.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.sctp ↗.interfaceTableModule	string
ue.sctp ↗.routingTableModule	string
ue.sctp ↗.checksumMode	string	“declared”
ue.sctp ↗.numGapReports	int	3
ue.sctp ↗.rtoInitial	double	3s
ue.sctp ↗.rtoMin	double	1s
ue.sctp ↗.rtoMax	double	60s
ue.sctp ↗.rtoAlpha	double	0.125
ue.sctp ↗.rtoBeta	double	0.250
ue.sctp ↗.maxBurst	int	4
ue.sctp ↗.maxBurstVariant	string	“maxBurst”
ue.sctp ↗.initialWindow	int	0
ue.sctp ↗.assocMaxRetrans	int	10
ue.sctp ↗.pathMaxRetrans	int	5
ue.sctp ↗.maxInitRetrans	int	8
ue.sctp ↗.sackPeriod	double	200ms
ue.sctp ↗.sackFrequency	int	2
ue.sctp ↗.reactivatePrimaryPath	bool	false
ue.sctp ↗.sendQueueLimit	int	0
ue.sctp ↗.validCookieLifetime	double	10s
ue.sctp ↗.enableHeartbeats	bool	true
ue.sctp ↗.hbInterval	double	30s
ue.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
ue.sctp ↗.nagleEnabled	bool	true
ue.sctp ↗.naglePoint	int	1468
ue.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
ue.sctp ↗.fastRecoverySupported	bool	true
ue.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
ue.sctp ↗.ccModule	int	0	RFC4960=0
ue.sctp ↗.osbWithHeader	bool	false
ue.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
ue.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
ue.sctp ↗.arwnd	int	65535
ue.sctp ↗.swsLimit	int	3000	Limit for SWS
ue.sctp ↗.udpEncapsEnabled	bool	false
ue.sctp ↗.natFriendly	bool	false
ue.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
ue.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
ue.sctp ↗.tellArwnd	bool	false	For flow control
ue.sctp ↗.messageAcceptLimit	int	0	For flow control
ue.sctp ↗.fairStart	double	0s
ue.sctp ↗.fairStop	double	0s
ue.sctp ↗.streamsToPaths	string	“”
ue.sctp ↗.startEndToEndDelay	int	0
ue.sctp ↗.stopEndToEndDelay	int	10
ue.sctp ↗.throughputInterval	double	1
ue.sctp ↗.auth	bool	false
ue.sctp ↗.chunks	string	“”
ue.sctp ↗.padding	bool	false
ue.sctp ↗.addIP	bool	false
ue.sctp ↗.addTime	double	0s
ue.sctp ↗.addAddress	string	“”
ue.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
ue.sctp ↗.packetDrop	bool	false
ue.sctp ↗.sackNow	bool	false
ue.sctp ↗.highSpeedCC	bool	false
ue.sctp ↗.checkSackSeqNumber	bool	false
ue.sctp ↗.nrSack	bool	false
ue.sctp ↗.disableReneging	bool	false
ue.sctp ↗.gapReportLimit	int	100000000
ue.sctp ↗.gapListOptimizationVariant	string	“none”
ue.sctp ↗.smartOverfullSACKHandling	bool	false
ue.sctp ↗.allowQoSTracking	bool	false
ue.sctp ↗.qosTrackingInterval	double	1.0s
ue.sctp ↗.cmtSendAllVariant	string	“normal”
ue.sctp ↗.cmtRetransmissionVariant	string	“normal”
ue.sctp ↗.cmtCUCVariant	string	“normal”
ue.sctp ↗.cmtBufferSplitVariant	string	“none”
ue.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
ue.sctp ↗.cmtUseSFR	bool	true
ue.sctp ↗.cmtUseDAC	bool	true
ue.sctp ↗.cmtUseFRC	bool	true
ue.sctp ↗.cmtSmartT3Reset	bool	true
ue.sctp ↗.cmtSmartFastRTX	bool	true
ue.sctp ↗.cmtSmartReneging	bool	false
ue.sctp ↗.cmtSlowPathRTTUpdate	bool	false
ue.sctp ↗.cmtChunkReschedulingVariant	string	“none”
ue.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
ue.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
ue.sctp ↗.movedChunkFastRTXFactor	double	2.0
ue.sctp ↗.cmtSackPath	string	“standard”
ue.sctp ↗.strictCwndBooking	bool	false
ue.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
ue.sctp ↗.cmtCCPathGroups	string	“”
ue.sctp ↗.rpPathBlocking	bool	false
ue.sctp ↗.rpScaleBlockingTimeout	bool	false
ue.sctp ↗.rpMinCwnd	int	1
ue.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.quic ↗.routingTableModule	string		Set by StandardHost.
ue.quic ↗.sendZeroRttTokenAsServer	bool	false
ue.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
ue.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
ue.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
ue.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
ue.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
ue.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
ue.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
ue.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
ue.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
ue.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
ue.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
ue.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
ue.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
ue.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
ue.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
ue.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
ue.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
ue.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
ue.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
ue.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
ue.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
ue.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
ue.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
ue.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
ue.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
ue.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
ue.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
ue.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
ue.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
ue.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.tn ↗.forwardServiceRegistration	bool	true
ue.tn ↗.forwardProtocolRegistration	bool	true
ue.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ue.at ↗.forwardServiceRegistration	bool	true
ue.at ↗.forwardProtocolRegistration	bool	true
ue.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ue.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ue.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ue.cellularNic.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.cellularNic.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ue.cellularNic.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ue.cellularNic.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ue.cellularNic.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ue.cellularNic.pcapRecorder ↗.fileFormat	string	“pcapng”
ue.cellularNic.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ue.cellularNic.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ue.cellularNic.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ue.cellularNic.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ue.cellularNic.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ue.cellularNic.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ue.cellularNic.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ue.cellularNic.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ue.cellularNic.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ue.cellularNic.handoverPacketHolder.sessionType	string		The type of the UE’s session (see LteUe): the IP types parse the uplink datagram’s header for the modules after this one, the others carry the payload as is
ue.cellularNic.ip2nic.binderModule	string	“binder”
ue.cellularNic.ip2nic.connectionControlModule	string	“^.rrc.connectionControl”	The node’s control-plane entry point, asked for a bearer on a lookup miss
ue.cellularNic.ip2nic.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb, or in the ini for a DC master eNB)
ue.cellularNic.ip2nic.hasSdap	bool	false	When true, SDAP handles DRB/RLC assignment; Ip2Nic skips traffic classification
ue.cellularNic.ip2nic.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe), which the payload the NIC delivers up is of; set by the NIC
ue.cellularNic.ip2nic.establishBearersOnDemand	bool	true	When false, a packet that finds no established bearer raises an error instead of establishing one (static bearers are established up front; see the staticDrbs parameter of BearerConfigurator)
ue.cellularNic.ip2nic.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
ue.cellularNic.rrc.registration.interfaceTableModule	string
ue.cellularNic.rrc.registration.interfaceName	string	“cellular”
ue.cellularNic.rrc.registration.routingTableModule	string
ue.cellularNic.rrc.registration.binderModule	string	“binder”
ue.cellularNic.rrc.registration.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), told about a multicast group join
ue.cellularNic.rrc.registration.sessionType	string	“”	UE only: the type of the UE’s session (see LteUe): a UE created during the run gets an IPv4 default route through the NIC only on an IP session, and the NIC of an Ethernet session is an Ethernet port; set by the NIC
ue.cellularNic.rrc.bearerManagement.binderModule	string	“binder”	To reach a peer’s BearerManagement on RLF
ue.cellularNic.rrc.bearerManagement.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point (see Rrc), which a torn-down bearer’s DRB identity goes back through
ue.cellularNic.rrc.bearerManagement.t311	double	0s	RRC re-establishment cell-selection timer (0 => release-to-IDLE)
ue.cellularNic.rrc.bearerManagement.t301	double	0.1s	RRC re-establishment (request -> complete) timer
ue.cellularNic.rrc.bearerManagement.headerCompressedSize	int	-1B	Removed, an error if set: header compression is configured per bearer (the rohc field of BearerConfigurator’s bearer definitions)
ue.cellularNic.rrc.bearerManagement.pdcpEntityModuleType	string	“simu5g.stack.pdcp.LtePdcpEntity”	PDCP entity types: the full PDCP entity is a compound (PdcpEntityBase, TX+RX sides plus the leg split/join stage of a multi-leg bearer); the instantiable types are its subclasses (LtePdcpEntity, NrPdcpEntity). At a DC secondary a bearer’s PDCP lives at the master, so the secondary installs an PdcpRelayEntity (tunnels PDUs to/from the master) in its place.
ue.cellularNic.rrc.bearerManagement.pdcpRelayEntityModuleType	string	“simu5g.stack.pdcp.PdcpRelayEntity”
ue.cellularNic.rrc.bearerManagement.dualConnectivityEnabled	bool	false	Set by the NIC; two-leg (split-capable) bearers
ue.cellularNic.rrc.bearerManagement.rlcTmEntityModuleType	string	“simu5g.stack.rlc.RlcTmEntity”	RLC entity types (compound modules): lteRlc* = LTE-FI bearers (TS 36.322), nrRlc* = NR bearers (SI/SO wire format, TS 38.322)
ue.cellularNic.rrc.bearerManagement.lteRlcUmEntityModuleType	string	“simu5g.stack.rlc.LteRlcUmEntity”
ue.cellularNic.rrc.bearerManagement.lteRlcAmEntityModuleType	string	“simu5g.stack.rlc.LteRlcAmEntity”
ue.cellularNic.rrc.bearerManagement.nrRlcUmEntityModuleType	string	“simu5g.stack.rlc.NrRlcUmEntity”
ue.cellularNic.rrc.bearerManagement.nrRlcAmEntityModuleType	string	“simu5g.stack.rlc.NrRlcAmEntity”
ue.cellularNic.rrc.bearerManagement.registrationModule	string	“^.registration”	Module references for accessing other stack layers
ue.cellularNic.rrc.bearerManagement.drbTableModule	string	“^.drbTable”
ue.cellularNic.rrc.bearerManagement.ip2nicModule	string	“^.^.ip2nic”
ue.cellularNic.rrc.bearerManagement.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”	Attachment-ledger push target (UE only)
ue.cellularNic.rrc.bearerManagement.pdcpMuxModule	string	“^.^.pdcpMux”
ue.cellularNic.rrc.bearerManagement.pdcpDcMuxModule	string	“^.^.pdcpDcMux”
ue.cellularNic.rrc.bearerManagement.d2dModeControllerModule	string	“^.d2dModeController”
ue.cellularNic.rrc.bearerManagement.rlcMuxModule	string	“^.^.rlcMux”
ue.cellularNic.rrc.bearerManagement.nrRlcMuxModule	string	“^.^.nrRlcMux”
ue.cellularNic.rrc.bearerManagement.macModule	string	“^.^.mac”
ue.cellularNic.rrc.bearerManagement.nrMacModule	string	“^.^.nrMac”
ue.cellularNic.rrc.bearerManagement.sdapModule	string	“^.^.sdap”	Configuration push target; unresolvable (no SDAP on the NIC) = no pushes
ue.cellularNic.rrc.bearerManagement.qosFlowClassifierModule	string	“^.^.qosFlowClassifier”	Uplink QFI rule push target; unresolvable (not a UE stack with SDAP) = no pushes
ue.cellularNic.rrc.connectionControl.binderModule	string	“binder”
ue.cellularNic.rrc.connectionControl.bearerConfiguratorModule	string	“bearerConfigurator”
ue.cellularNic.rrc.connectionControl.coreControlModule	string	“coreControl”
ue.cellularNic.rrc.connectionControl.bearerManagementModule	string	“^.bearerManagement”
ue.cellularNic.rrc.connectionControl.macModule	string	“^.^.mac”
ue.cellularNic.rrc.connectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
ue.cellularNic.rrc.connectionControl.gtpUserModule	string	“^.^.^.relay.gtpUser”
ue.cellularNic.rrc.connectionControl.gtpUserX2Module	string	“^.^.^.gtpUserX2”
ue.cellularNic.rrc.connectionControl.macNodeId	int		The base station’s node id; the NIC sets it from the node’s
ue.cellularNic.rrc.connectionControl.gateway	string	“”	The node’s core network gateway, as its gateway parameter names it; ignored at a node not connected to a core network (a secondary node)
ue.cellularNic.rrc.nrConnectionControl.dynamicCellAssociation	bool	false
ue.cellularNic.rrc.nrConnectionControl.enableHandover	bool	false	Allows handovers in the UE
ue.cellularNic.rrc.nrConnectionControl.isNr	bool		Whether this instance is associated with the NR or the LTE stack
ue.cellularNic.rrc.nrConnectionControl.macNodeId	int		MacNodeId of the stack leg this controller belongs to (set by the NIC)
ue.cellularNic.rrc.nrConnectionControl.sessionType	string		The type of the session the UE requests at connection setup (see LteUe), set by the NIC
ue.cellularNic.rrc.nrConnectionControl.handoverLatency	double	50ms	Handover duration
ue.cellularNic.rrc.nrConnectionControl.handoverDetachmentTime	double	handoverLatency > 0s ? handoverLatency/2 : 25ms
ue.cellularNic.rrc.nrConnectionControl.handoverAttachmentTime	double	handoverLatency > 0s ? handoverLatency-handoverDetachmentTime : handoverDetachmentTime
ue.cellularNic.rrc.nrConnectionControl.minRssiDefault	bool	true	Whether minRssi is taken from PhyPisaData instead of the minRssi parameter
ue.cellularNic.rrc.nrConnectionControl.minRssi	double	-99.0dB	Configurable minimum threshold RSSI for attaching to an eNB (meaningful only if minRssiDefault==false)
ue.cellularNic.rrc.nrConnectionControl.hysteresisFactor	double	10
ue.cellularNic.rrc.nrConnectionControl.binderModule	string	“binder”
ue.cellularNic.rrc.nrConnectionControl.macModule	string	“^.^.mac”
ue.cellularNic.rrc.nrConnectionControl.bearerManagementModule	string	“^.bearerManagement”
ue.cellularNic.rrc.nrConnectionControl.handoverPacketHolderModule	string	“^.^.handoverPacketHolder”
ue.cellularNic.rrc.nrConnectionControl.feedbackGeneratorModule	string	“^.^.dlFbGen”	TODO or “^.^.nrDlFbGen”
ue.cellularNic.rrc.nrConnectionControl.otherConnectionControlModule	string	“”
ue.cellularNic.rrc.nrConnectionControl.hasCollector	bool	false	True when node has a collector module (ueCollector/nrUeCollector) for this PHY module
ue.cellularNic.rrc.d2dModeSelection.modeSelectionPeriod	double	1s
ue.cellularNic.rrc.d2dModeSelection.binderModule	string	“binder”
ue.cellularNic.rrc.d2dModeSelection.d2dBinderModule	string	“d2dBinder”	The network’s D2dBinder, which holds the D2D state
ue.cellularNic.rrc.d2dModeSelection.macModule	string	“^.^.mac”
ue.cellularNic.rrc.d2dModeSelection.connectionControlModule	string	“^.connectionControl”	The node’s control-plane entry point, which knows the UEs handing over
ue.cellularNic.rlcMux.bearerManagementModule	string	“^.rrc.bearerManagement”
ue.cellularNic.phy.isNr	bool	false	True for the NR leg (set by NrNicUe/NrNicEnb on their PHY submodule)
ue.cellularNic.phy.macNodeId	int		MacNodeId of the stack leg this PHY belongs to (set by the NIC)
ue.cellularNic.phy.ueTxPower	double	26dBm
ue.cellularNic.phy.eNodeBTxPower	double	46dBm
ue.cellularNic.phy.microTxPower	double	30dBm
ue.cellularNic.phy.txDirection	string	“OMNI”
ue.cellularNic.phy.txAngle	double	0deg
ue.cellularNic.phy.binderModule	string	“binder”
ue.cellularNic.phy.channelModelModule	string	“^.channelModel[0]”	Set to “^.nrChannelModel[0]” on an NR leg, see NrNicUe
ue.cellularNic.phy.connectionControlModule	string	“^.rrc.connectionControl”
ue.cellularNic.packetFlowObserver.macModule	string	“^.mac”
ue.cellularNic.packetFlowObserver.pdcpModule	string	“^”
ue.cellularNic.packetFlowObserver.rlcModule	string	“^”
ue.cellularNic.packetFlowObserver.isNrObserver	bool	false
ue.cellularNic.packetFlowObserver.pfmType	string	“PacketFlowObserverUe”
ue.cellularNic.dlFbGen.isNr	bool	false	True for the NR leg (set by NrNicUe on the nrDlFbGen submodule)
ue.cellularNic.dlFbGen.macNodeId	int		MacNodeId of the stack leg this generator belongs to (set by the NIC)
ue.cellularNic.dlFbGen.feedbackType	string	“ALLBANDS”	Can be ALLBANDS, PREFERRED, WIDEBAND
ue.cellularNic.dlFbGen.rbAllocationType	string	“localized”	Resource allocation type (“distributed” or “localized”)
ue.cellularNic.dlFbGen.fbPeriod	int	6tti	Period for Periodic feedback in TTI
ue.cellularNic.dlFbGen.fbDelay	int	1tti	Time interval between sensing and transmission in TTI
ue.cellularNic.dlFbGen.usePeriodic	bool	true	Whether periodic feedback is used in addition to aperiodic feedback
ue.cellularNic.dlFbGen.initialTxMode	string	“SINGLE_ANTENNA_PORT0”	Initial txMode (see LteCommon.h)
ue.cellularNic.dlFbGen.binderModule	string	“binder”
ue.cellularNic.dlFbGen.phyModule	string	“^.phy”
ue.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.macTable ↗.agingTime	double	120s
ue.macTable ↗.forwardingTable	object	[]
ue.macTable ↗.forwardingTableFile	string	“”
ue.macTable ↗.interfaceTableModule	string
ue.unstructuredApp.source ↗.displayStringTextFormat	string	“created %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.unstructuredApp.source ↗.packetNameFormat	string	“%a-%c”	See directives in module documentation
ue.unstructuredApp.source ↗.packetRepresentation	string	“byteCount”	Determines the chunk of the packet data
ue.unstructuredApp.source ↗.packetProtocol	string	“unknown”
ue.unstructuredApp.source ↗.packetLength	int
ue.unstructuredApp.source ↗.packetData	int	-1
ue.unstructuredApp.source ↗.attachCreationTimeTag	bool	true
ue.unstructuredApp.source ↗.attachIdentityTag	bool	true
ue.unstructuredApp.source ↗.attachDirectionTag	bool	true
ue.unstructuredApp.source ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
ue.unstructuredApp.source ↗.initialProductionOffset	double	-1s	Initial duration before which packets are not produced. When negative, then produce packet in initialize()
ue.unstructuredApp.source ↗.productionInterval	double		Elapsed time between subsequent packets pushed to the connected packet consumer
ue.unstructuredApp.source ↗.scheduleForAbsoluteTime	bool	true	When a clock is used, “relative” means that setting the clock will not affect the simulation time of the event
ue.unstructuredApp.sink ↗.displayStringTextFormat	string	“received %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ue.unstructuredApp.sink ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
ue.unstructuredApp.sink ↗.initialConsumptionOffset	double	0s	Initial duration before which packets are not consumed
ue.unstructuredApp.sink ↗.consumptionInterval	double	0s	Elapsed time between subsequent packets allowed to be pushed by the connected packet producer, 0 means any number of packets can be pushed at the same simulation time
ue.unstructuredApp.sink ↗.scheduleForAbsoluteTime	bool	true	When a clock is used, “relative” means that setting the clock will not affect the simulation time of the event
ue.unstructuredApp.io.interfaceTableModule	string		Relative module path of the interface table
ue.unstructuredApp.io.interface	string	“cellular”	The name of the cellular NIC’s interface
mecHost1.virtualisationInfrastructure.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.virtualisationInfrastructure.pppIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.mtu	int	4470B
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost1.virtualisationInfrastructure.pppIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.virtualisationInfrastructure.extEth ↗.socket ↗.displayStringTextFormat	string	“device: {device}\nsnt:{numSent} rcv:{numReceived}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.extEth ↗.socket ↗.device	string		Name of an existing real Ethernet device
mecHost1.virtualisationInfrastructure.extEth ↗.socket ↗.namespace	string	“”
mecHost1.virtualisationInfrastructure.extEth ↗.socket ↗.packetNameFormat	string	“Ext-%p-%t-%n”	Name of received packets
mecHost1.virtualisationInfrastructure.encap ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.encap ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.encap ↗.fcsMode	string	“declared”
mecHost1.virtualisationInfrastructure.encap ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
mecHost1.virtualisationInfrastructure.encap ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.virtualisationInfrastructure.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.lo ↗.lo ↗.mtu	int	4470B
mecHost1.virtualisationInfrastructure.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.configurator ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
mecHost1.virtualisationInfrastructure.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost1.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
mecHost1.virtualisationInfrastructure.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
mecHost1.virtualisationInfrastructure.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.enabled	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.queryInterval	double	125s
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
mecHost1.virtualisationInfrastructure.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
mecHost1.virtualisationInfrastructure.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.icmp ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.arpModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.icmpModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.timeToLive	int	32
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
mecHost1.virtualisationInfrastructure.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
mecHost1.virtualisationInfrastructure.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.interfaceTableModule	string
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.spdConfig	xml
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.configurator ↗.interfaceTableModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.configurator ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
mecHost1.virtualisationInfrastructure.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.forwarding	bool	false
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
mecHost1.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
mecHost1.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.routingTableModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.icmpv6Module	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.procDelay	double	0s
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.interfaceTableModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.spdConfig	xml
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost1.virtualisationInfrastructure.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.isMobileNode	bool
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
mecHost1.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
mecHost1.virtualisationInfrastructure.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
mecHost1.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
mecHost1.virtualisationInfrastructure.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
mecHost1.virtualisationInfrastructure.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.virtualisationInfrastructure.udp ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.udp ↗.defaultMulticastLoop	bool	true
mecHost1.virtualisationInfrastructure.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.tcp ↗.checksumMode	string	“declared”
mecHost1.virtualisationInfrastructure.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
mecHost1.virtualisationInfrastructure.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
mecHost1.virtualisationInfrastructure.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
mecHost1.virtualisationInfrastructure.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
mecHost1.virtualisationInfrastructure.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
mecHost1.virtualisationInfrastructure.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
mecHost1.virtualisationInfrastructure.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
mecHost1.virtualisationInfrastructure.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
mecHost1.virtualisationInfrastructure.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
mecHost1.virtualisationInfrastructure.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
mecHost1.virtualisationInfrastructure.tcp ↗.msl	int	120s	Maximum Segment Lifetime
mecHost1.virtualisationInfrastructure.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
mecHost1.virtualisationInfrastructure.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
mecHost1.virtualisationInfrastructure.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
mecHost1.virtualisationInfrastructure.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
mecHost1.virtualisationInfrastructure.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost1.virtualisationInfrastructure.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
mecHost1.virtualisationInfrastructure.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
mecHost1.virtualisationInfrastructure.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
mecHost1.virtualisationInfrastructure.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
mecHost1.virtualisationInfrastructure.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.at ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.at ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.tn ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.tn ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.virtualisationInfrastructure.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.virtualisationInfrastructure.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.virtualisationInfrastructure.nl ↗.forwardServiceRegistration	bool	true
mecHost1.virtualisationInfrastructure.nl ↗.forwardProtocolRegistration	bool	true
mecHost1.virtualisationInfrastructure.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.virtualisationInfrastructure.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.virtualisationInfrastructure.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.mecPlatform.serviceRegistry.serviceName	string	“ServiceRegistry”
mecHost1.mecPlatform.serviceRegistry.requestQueueSize	int	0
mecHost1.mecPlatform.serviceRegistry.subscriptionQueueSize	int	0
mecHost1.mecPlatform.serviceRegistry.localAddress	string	“”	Local address; may be left empty (“”)
mecHost1.mecPlatform.serviceRegistry.localPort	int	1000	localPort number to listen on
mecHost1.mecPlatform.serviceRegistry.requestServiceTime	double	15us
mecHost1.mecPlatform.serviceRegistry.subscriptionServiceTime	double	20us
mecHost1.mecPlatform.serviceRegistry.serverThreadClass	string	“simu5g.mec.platform.services.base.SocketManager”
mecHost1.mecPlatform.serviceRegistry.tos	int	-1	If not -1, set the Type of Service (IPv4) / Traffic Class (IPv6) field of sent packets to this value
mecHost1.mecPlatform.serviceRegistry.binderModule	string	“binder”
mecHost1.mecPlatformManager.mecOrchestrator	string
mecHost1.mecPlatformManager.serviceRegistryModule	string	“^.mecPlatform.serviceRegistry”
mecHost1.mecPlatformManager.vimModule	string	“^.vim”
mecHost1.vim.binderModule	string	“binder”
mecHost1.vim.mp1Port	int	10021
mecHost1.vim.scheduling	string	“segregation”
mecHost1.upf_mec.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.status ↗.initialStatus	string	“UP”	Initial status of the network node
mecHost1.upf_mec.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.environment ↗.initStage	int	0	Initialization stage for the setup command
mecHost1.upf_mec.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
mecHost1.upf_mec.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
mecHost1.upf_mec.environment ↗.setupCommand	string	“”	A host OS system command
mecHost1.upf_mec.environment ↗.teardownCommand	string	“”	A host OS system command
mecHost1.upf_mec.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
mecHost1.upf_mec.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost1.upf_mec.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.cb ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.cb ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.bl ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.bl ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
mecHost1.upf_mec.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ethernet ↗.fcsMode	string	“declared”
mecHost1.upf_mec.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
mecHost1.upf_mec.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
mecHost1.upf_mec.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.li ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.li ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.lo ↗.lo ↗.mtu	int	4470B
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.wlan ↗.agent ↗.mibModule	string
mecHost1.upf_mec.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
mecHost1.upf_mec.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
mecHost1.upf_mec.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
mecHost1.upf_mec.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
mecHost1.upf_mec.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
mecHost1.upf_mec.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
mecHost1.upf_mec.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
mecHost1.upf_mec.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
mecHost1.upf_mec.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
mecHost1.upf_mec.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
mecHost1.upf_mec.wlan ↗.mgmt ↗.mibModule	string
mecHost1.upf_mec.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
mecHost1.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
mecHost1.upf_mec.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.ds ↗.mibModule	string
mecHost1.upf_mec.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.wlan ↗.mac ↗.tx ↗.rxModule	string
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost1.upf_mec.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.upf_mec.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.upf_mec.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost1.upf_mec.ppp ↗.ppp ↗.mtu	int	4470B
mecHost1.upf_mec.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost1.upf_mec.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.tun ↗.tun ↗.mtu	int	1500B
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.virt ↗.tunnel ↗.interfaceTableModule	string
mecHost1.upf_mec.virt ↗.tunnel ↗.realInterface	string
mecHost1.upf_mec.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
mecHost1.upf_mec.virt ↗.tunnel ↗.address	string	“copy”
mecHost1.upf_mec.virt ↗.tunnel ↗.vlanId	int	-1
mecHost1.upf_mec.virt ↗.tunnel ↗.steal	bool	vlanId != -1
mecHost1.upf_mec.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.configurator ↗.routingTableModule	string
mecHost1.upf_mec.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
mecHost1.upf_mec.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost1.upf_mec.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
mecHost1.upf_mec.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
mecHost1.upf_mec.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
mecHost1.upf_mec.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.igmp ↗.routingTableModule	string
mecHost1.upf_mec.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
mecHost1.upf_mec.ipv4 ↗.igmp ↗.enabled	bool	true
mecHost1.upf_mec.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
mecHost1.upf_mec.ipv4 ↗.igmp ↗.queryInterval	double	125s
mecHost1.upf_mec.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
mecHost1.upf_mec.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
mecHost1.upf_mec.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
mecHost1.upf_mec.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
mecHost1.upf_mec.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
mecHost1.upf_mec.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
mecHost1.upf_mec.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
mecHost1.upf_mec.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
mecHost1.upf_mec.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.icmp ↗.routingTableModule	string
mecHost1.upf_mec.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
mecHost1.upf_mec.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
mecHost1.upf_mec.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.ip ↗.routingTableModule	string
mecHost1.upf_mec.ipv4 ↗.ip ↗.arpModule	string
mecHost1.upf_mec.ipv4 ↗.ip ↗.icmpModule	string
mecHost1.upf_mec.ipv4 ↗.ip ↗.checksumMode	string	“declared”
mecHost1.upf_mec.ipv4 ↗.ip ↗.timeToLive	int	32
mecHost1.upf_mec.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
mecHost1.upf_mec.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
mecHost1.upf_mec.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
mecHost1.upf_mec.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
mecHost1.upf_mec.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
mecHost1.upf_mec.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
mecHost1.upf_mec.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
mecHost1.upf_mec.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv4 ↗.arp ↗.routingTableModule	string
mecHost1.upf_mec.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
mecHost1.upf_mec.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
mecHost1.upf_mec.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
mecHost1.upf_mec.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.interfaceTableModule	string
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.spdConfig	xml
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost1.upf_mec.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost1.upf_mec.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.configurator ↗.interfaceTableModule	string
mecHost1.upf_mec.ipv6 ↗.configurator ↗.routingTableModule	string
mecHost1.upf_mec.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
mecHost1.upf_mec.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.forwarding	bool	false
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
mecHost1.upf_mec.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
mecHost1.upf_mec.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
mecHost1.upf_mec.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
mecHost1.upf_mec.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
mecHost1.upf_mec.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.routingTableModule	string
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.icmpv6Module	string
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.procDelay	double	0s
mecHost1.upf_mec.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.interfaceTableModule	string
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.spdConfig	xml
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost1.upf_mec.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost1.upf_mec.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.isMobileNode	bool
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
mecHost1.upf_mec.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
mecHost1.upf_mec.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
mecHost1.upf_mec.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
mecHost1.upf_mec.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost1.upf_mec.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
mecHost1.upf_mec.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
mecHost1.upf_mec.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
mecHost1.upf_mec.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
mecHost1.upf_mec.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
mecHost1.upf_mec.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
mecHost1.upf_mec.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
mecHost1.upf_mec.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
mecHost1.upf_mec.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
mecHost1.upf_mec.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
mecHost1.upf_mec.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
mecHost1.upf_mec.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
mecHost1.upf_mec.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.nl ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.nl ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.udp ↗.checksumMode	string	“declared”
mecHost1.upf_mec.udp ↗.defaultMulticastLoop	bool	true
mecHost1.upf_mec.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.tcp ↗.checksumMode	string	“declared”
mecHost1.upf_mec.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
mecHost1.upf_mec.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
mecHost1.upf_mec.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
mecHost1.upf_mec.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
mecHost1.upf_mec.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
mecHost1.upf_mec.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
mecHost1.upf_mec.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
mecHost1.upf_mec.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
mecHost1.upf_mec.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
mecHost1.upf_mec.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
mecHost1.upf_mec.tcp ↗.msl	int	120s	Maximum Segment Lifetime
mecHost1.upf_mec.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
mecHost1.upf_mec.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
mecHost1.upf_mec.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
mecHost1.upf_mec.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
mecHost1.upf_mec.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost1.upf_mec.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
mecHost1.upf_mec.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
mecHost1.upf_mec.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
mecHost1.upf_mec.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
mecHost1.upf_mec.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.sctp ↗.interfaceTableModule	string
mecHost1.upf_mec.sctp ↗.routingTableModule	string
mecHost1.upf_mec.sctp ↗.checksumMode	string	“declared”
mecHost1.upf_mec.sctp ↗.numGapReports	int	3
mecHost1.upf_mec.sctp ↗.rtoInitial	double	3s
mecHost1.upf_mec.sctp ↗.rtoMin	double	1s
mecHost1.upf_mec.sctp ↗.rtoMax	double	60s
mecHost1.upf_mec.sctp ↗.rtoAlpha	double	0.125
mecHost1.upf_mec.sctp ↗.rtoBeta	double	0.250
mecHost1.upf_mec.sctp ↗.maxBurst	int	4
mecHost1.upf_mec.sctp ↗.maxBurstVariant	string	“maxBurst”
mecHost1.upf_mec.sctp ↗.initialWindow	int	0
mecHost1.upf_mec.sctp ↗.assocMaxRetrans	int	10
mecHost1.upf_mec.sctp ↗.pathMaxRetrans	int	5
mecHost1.upf_mec.sctp ↗.maxInitRetrans	int	8
mecHost1.upf_mec.sctp ↗.sackPeriod	double	200ms
mecHost1.upf_mec.sctp ↗.sackFrequency	int	2
mecHost1.upf_mec.sctp ↗.reactivatePrimaryPath	bool	false
mecHost1.upf_mec.sctp ↗.sendQueueLimit	int	0
mecHost1.upf_mec.sctp ↗.validCookieLifetime	double	10s
mecHost1.upf_mec.sctp ↗.enableHeartbeats	bool	true
mecHost1.upf_mec.sctp ↗.hbInterval	double	30s
mecHost1.upf_mec.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
mecHost1.upf_mec.sctp ↗.nagleEnabled	bool	true
mecHost1.upf_mec.sctp ↗.naglePoint	int	1468
mecHost1.upf_mec.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
mecHost1.upf_mec.sctp ↗.fastRecoverySupported	bool	true
mecHost1.upf_mec.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
mecHost1.upf_mec.sctp ↗.ccModule	int	0	RFC4960=0
mecHost1.upf_mec.sctp ↗.osbWithHeader	bool	false
mecHost1.upf_mec.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
mecHost1.upf_mec.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
mecHost1.upf_mec.sctp ↗.arwnd	int	65535
mecHost1.upf_mec.sctp ↗.swsLimit	int	3000	Limit for SWS
mecHost1.upf_mec.sctp ↗.udpEncapsEnabled	bool	false
mecHost1.upf_mec.sctp ↗.natFriendly	bool	false
mecHost1.upf_mec.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
mecHost1.upf_mec.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
mecHost1.upf_mec.sctp ↗.tellArwnd	bool	false	For flow control
mecHost1.upf_mec.sctp ↗.messageAcceptLimit	int	0	For flow control
mecHost1.upf_mec.sctp ↗.fairStart	double	0s
mecHost1.upf_mec.sctp ↗.fairStop	double	0s
mecHost1.upf_mec.sctp ↗.streamsToPaths	string	“”
mecHost1.upf_mec.sctp ↗.startEndToEndDelay	int	0
mecHost1.upf_mec.sctp ↗.stopEndToEndDelay	int	10
mecHost1.upf_mec.sctp ↗.throughputInterval	double	1
mecHost1.upf_mec.sctp ↗.auth	bool	false
mecHost1.upf_mec.sctp ↗.chunks	string	“”
mecHost1.upf_mec.sctp ↗.padding	bool	false
mecHost1.upf_mec.sctp ↗.addIP	bool	false
mecHost1.upf_mec.sctp ↗.addTime	double	0s
mecHost1.upf_mec.sctp ↗.addAddress	string	“”
mecHost1.upf_mec.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
mecHost1.upf_mec.sctp ↗.packetDrop	bool	false
mecHost1.upf_mec.sctp ↗.sackNow	bool	false
mecHost1.upf_mec.sctp ↗.highSpeedCC	bool	false
mecHost1.upf_mec.sctp ↗.checkSackSeqNumber	bool	false
mecHost1.upf_mec.sctp ↗.nrSack	bool	false
mecHost1.upf_mec.sctp ↗.disableReneging	bool	false
mecHost1.upf_mec.sctp ↗.gapReportLimit	int	100000000
mecHost1.upf_mec.sctp ↗.gapListOptimizationVariant	string	“none”
mecHost1.upf_mec.sctp ↗.smartOverfullSACKHandling	bool	false
mecHost1.upf_mec.sctp ↗.allowQoSTracking	bool	false
mecHost1.upf_mec.sctp ↗.qosTrackingInterval	double	1.0s
mecHost1.upf_mec.sctp ↗.cmtSendAllVariant	string	“normal”
mecHost1.upf_mec.sctp ↗.cmtRetransmissionVariant	string	“normal”
mecHost1.upf_mec.sctp ↗.cmtCUCVariant	string	“normal”
mecHost1.upf_mec.sctp ↗.cmtBufferSplitVariant	string	“none”
mecHost1.upf_mec.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
mecHost1.upf_mec.sctp ↗.cmtUseSFR	bool	true
mecHost1.upf_mec.sctp ↗.cmtUseDAC	bool	true
mecHost1.upf_mec.sctp ↗.cmtUseFRC	bool	true
mecHost1.upf_mec.sctp ↗.cmtSmartT3Reset	bool	true
mecHost1.upf_mec.sctp ↗.cmtSmartFastRTX	bool	true
mecHost1.upf_mec.sctp ↗.cmtSmartReneging	bool	false
mecHost1.upf_mec.sctp ↗.cmtSlowPathRTTUpdate	bool	false
mecHost1.upf_mec.sctp ↗.cmtChunkReschedulingVariant	string	“none”
mecHost1.upf_mec.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
mecHost1.upf_mec.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
mecHost1.upf_mec.sctp ↗.movedChunkFastRTXFactor	double	2.0
mecHost1.upf_mec.sctp ↗.cmtSackPath	string	“standard”
mecHost1.upf_mec.sctp ↗.strictCwndBooking	bool	false
mecHost1.upf_mec.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
mecHost1.upf_mec.sctp ↗.cmtCCPathGroups	string	“”
mecHost1.upf_mec.sctp ↗.rpPathBlocking	bool	false
mecHost1.upf_mec.sctp ↗.rpScaleBlockingTimeout	bool	false
mecHost1.upf_mec.sctp ↗.rpMinCwnd	int	1
mecHost1.upf_mec.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.quic ↗.routingTableModule	string		Set by StandardHost.
mecHost1.upf_mec.quic ↗.sendZeroRttTokenAsServer	bool	false
mecHost1.upf_mec.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
mecHost1.upf_mec.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
mecHost1.upf_mec.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
mecHost1.upf_mec.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
mecHost1.upf_mec.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
mecHost1.upf_mec.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
mecHost1.upf_mec.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
mecHost1.upf_mec.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
mecHost1.upf_mec.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
mecHost1.upf_mec.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
mecHost1.upf_mec.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
mecHost1.upf_mec.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
mecHost1.upf_mec.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
mecHost1.upf_mec.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
mecHost1.upf_mec.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
mecHost1.upf_mec.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
mecHost1.upf_mec.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
mecHost1.upf_mec.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
mecHost1.upf_mec.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
mecHost1.upf_mec.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
mecHost1.upf_mec.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
mecHost1.upf_mec.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
mecHost1.upf_mec.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
mecHost1.upf_mec.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
mecHost1.upf_mec.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
mecHost1.upf_mec.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
mecHost1.upf_mec.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
mecHost1.upf_mec.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
mecHost1.upf_mec.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
mecHost1.upf_mec.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.tn ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.tn ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.at ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.at ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.dnPpp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.dnPpp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnPpp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost1.upf_mec.dnPpp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.upf_mec.dnPpp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.dnPpp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.dnPpp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.upf_mec.dnPpp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnPpp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost1.upf_mec.dnPpp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost1.upf_mec.dnPpp ↗.ppp ↗.mtu	int	4470B
mecHost1.upf_mec.dnPpp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost1.upf_mec.dnPpp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost1.upf_mec.relay.trafficFlowFilter.binderModule	string	“binder”
mecHost1.upf_mec.relay.trafficFlowFilter.fastForwarding	bool	true
mecHost1.upf_mec.relay.gtpUser.binderModule	string	“binder”
mecHost1.upf_mec.relay.gtpUser.localPort	int	31
mecHost1.upf_mec.relay.gtpUser.tunnelPeerPort	int	31
mecHost1.upf_mec.rd ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.rd ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.rd ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.nodeControl.binderModule	string	“binder”
mecHost1.upf_mec.nodeControl.gtpUserModule	string	“^.relay.gtpUser”
mecHost1.upf_mec.nodeControl.trafficFlowFilterModule	string	“^.relay.trafficFlowFilter”
mecHost1.upf_mec.nodeControl.ethernetBridgeModule	string	“^.ethBridge.sessionMux”	The node’s Ethernet session bridge (see EthernetSessionBridge), if it has one
mecHost1.upf_mec.nodeControl.unstructuredPrefix	string	“”	The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. “2001:db8:5::/64” or “10.5.0.0/16”; empty = the node anchors no Unstructured session (see the main comment)
mecHost1.upf_mec.nodeControl.unstructuredServer	string	“”	The application server the Unstructured sessions’ uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix
mecHost1.upf_mec.nodeControl.unstructuredServerPort	int	-1	The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions
mecHost1.upf_mec.nodeControl.unstructuredPort	int	-1	The UDP port the node receives the Unstructured sessions’ downlink on, and sends their uplink from; must be set for Unstructured sessions
mecHost1.upf_mec.ndResponder.binderModule	string	“binder”
mecHost1.upf_mec.ndResponder.linkLocalAddress	string	“fe80::1”	The router’s address on every session’s link
mecHost1.upf_mec.ndResponder.routerLifetime	double	9000s	Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)
mecHost1.upf_mec.ndResponder.curHopLimit	int	64	Cur Hop Limit in the Router Advertisements (0 = unspecified)
mecHost1.upf_mec.ndResponder.checksumMode	string	“declared”
mecHost1.upf_mec.ethBridge.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.macTable ↗.agingTime	double	120s
mecHost1.upf_mec.ethBridge.macTable ↗.forwardingTable	object	[]
mecHost1.upf_mec.ethBridge.macTable ↗.forwardingTableFile	string	“”
mecHost1.upf_mec.ethBridge.macTable ↗.interfaceTableModule	string
mecHost1.upf_mec.ethBridge.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost1.upf_mec.ethBridge.sessionMux.interfaceTableModule	string		The bridge’s interface table, which the session ports are registered in
mecHost1.upf_mec.ethBridge.sessionMux.macTableModule	string		The bridge’s MAC table, flushed of a released session’s port
mecHost1.upf_mec.ethBridge.sessionMux.portModuleType	string	“simu5g.corenetwork.ethernetSessionBridge.EthernetSessionPort”	The module type of the session ports
mecHost1.upf_mec.ethBridge.sessionMux.portDisplayString	string	“p=500,420,row,100;g=sessionPorts”	Display string of the session ports (their place in the bridge’s layout)
mecHost1.upf_mec.ethBridge.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ethBridge.cb ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ethBridge.cb ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ethBridge.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ethBridge.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ethBridge.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardVlan	bool	true
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardPcp	bool	true
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.excludeEncapsulationProtocols	object	[]
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.join ↗.displayStringTextFormat	string	“passed %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bridging ↗.directionReverser ↗.join ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.macTableModule	string		Relative module path of MAC table
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.interfaceTableModule	string		Relative module path of the interface table
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.macTableModule	string		Relative module path of MAC table
mecHost1.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.interfaceTableModule	string		Relative module path of interface table
mecHost1.upf_mec.ethBridge.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ethBridge.bl ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ethBridge.bl ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ethBridge.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ethBridge.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ethBridge.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.ethBridge.ethernet ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.socketCommandProcessor ↗.socketTableModule	string
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderInserter ↗.interfaceTableModule	string
mecHost1.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.minLength	int
mecHost1.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.roundingLength	int	1B
mecHost1.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.insertionPosition	string	“back”
mecHost1.upf_mec.ethBridge.ethernet ↗.fcsInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.fcsInserter ↗.fcsMode	string	“declared”
mecHost1.upf_mec.ethBridge.ethernet ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.socketPacketProcessor ↗.socketTableModule	string
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.backpressure	bool	false
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.interfaceTableModule	string
mecHost1.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.promiscuous	bool	false
mecHost1.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.backpressure	bool	false
mecHost1.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.popFcs	bool	true
mecHost1.upf_mec.ethBridge.ieee8021q ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.socketTableModule	string
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.vlanTagType	string	“c”
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.nextProtocol	string	“ethernetmac”
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultVlanId	int	-1
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultPcp	int	-1
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultUserPriority	int	-1
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultDropEligible	int	-1	<0: unspecified, 0: false, >0: true
mecHost1.upf_mec.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.socketTableModule	string
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.backpressure	bool	false
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanTagType	string	“c”
mecHost1.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanIdFilter	object	[]
mecHost1.upf_mec.ethBridge.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.ethBridge.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost1.upf_mec.ethBridge.li ↗.forwardServiceRegistration	bool	true
mecHost1.upf_mec.ethBridge.li ↗.forwardProtocolRegistration	bool	true
mecHost1.upf_mec.ethBridge.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost1.upf_mec.ethBridge.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost1.upf_mec.ethBridge.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost1.upf_mec.dnEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.packetCapacity	int	-1	Maximum number of packets in the queue, no limit by default
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.dropperClass	string	“”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost1.upf_mec.dnEth ↗.macLayer ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost1.upf_mec.dnEth ↗.macLayer ↗.server ↗.displayStringTextFormat	string	“served %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.macLayer ↗.server ↗.serveSchedulingPriority	int	0	Specifies the FES scheduling priority for the extra event that is pulling the packet, -1 means no extra event
mecHost1.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.direction	string	“undefined”
mecHost1.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.signalName	string
mecHost1.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.backpressure	bool	false
mecHost1.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.popFcs	bool	false
mecHost1.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.direction	string	“undefined”
mecHost1.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.signalName	string
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.displayStringTextFormat	string	“delayed %p pk (%l)\nifg: %g”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.initialChannelBusy	bool	false	Assume that the channel was busy before the simulation started
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.duration	double	96s / dropUnit(parent.bitrate)
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.direction	string	“undefined”
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.signalName	string
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.datarate	double	parent.bitrate
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.backpressure	bool	false
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.direction	string	“undefined”
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.signalName	string
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.receiver ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost1.upf_mec.dnEth ↗.phyLayer ↗.receiver ↗.datarate	double	parent.bitrate
mecHost2.virtualisationInfrastructure.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.virtualisationInfrastructure.pppIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.virtualisationInfrastructure.pppIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.mtu	int	4470B
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost2.virtualisationInfrastructure.pppIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.virtualisationInfrastructure.extEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.virtualisationInfrastructure.extEth ↗.socket ↗.displayStringTextFormat	string	“device: {device}\nsnt:{numSent} rcv:{numReceived}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.extEth ↗.socket ↗.device	string		Name of an existing real Ethernet device
mecHost2.virtualisationInfrastructure.extEth ↗.socket ↗.namespace	string	“”
mecHost2.virtualisationInfrastructure.extEth ↗.socket ↗.packetNameFormat	string	“Ext-%p-%t-%n”	Name of received packets
mecHost2.virtualisationInfrastructure.encap ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.encap ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.encap ↗.fcsMode	string	“declared”
mecHost2.virtualisationInfrastructure.encap ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
mecHost2.virtualisationInfrastructure.encap ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.virtualisationInfrastructure.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.virtualisationInfrastructure.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.lo ↗.lo ↗.mtu	int	4470B
mecHost2.virtualisationInfrastructure.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.configurator ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
mecHost2.virtualisationInfrastructure.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost2.virtualisationInfrastructure.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
mecHost2.virtualisationInfrastructure.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
mecHost2.virtualisationInfrastructure.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.enabled	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.queryInterval	double	125s
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
mecHost2.virtualisationInfrastructure.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
mecHost2.virtualisationInfrastructure.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.icmp ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.arpModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.icmpModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.timeToLive	int	32
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
mecHost2.virtualisationInfrastructure.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
mecHost2.virtualisationInfrastructure.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.interfaceTableModule	string
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.spdConfig	xml
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.configurator ↗.interfaceTableModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.configurator ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
mecHost2.virtualisationInfrastructure.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.forwarding	bool	false
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
mecHost2.virtualisationInfrastructure.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
mecHost2.virtualisationInfrastructure.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.routingTableModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.icmpv6Module	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.procDelay	double	0s
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.interfaceTableModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.spdConfig	xml
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost2.virtualisationInfrastructure.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.isMobileNode	bool
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
mecHost2.virtualisationInfrastructure.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
mecHost2.virtualisationInfrastructure.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
mecHost2.virtualisationInfrastructure.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
mecHost2.virtualisationInfrastructure.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
mecHost2.virtualisationInfrastructure.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.virtualisationInfrastructure.udp ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.udp ↗.defaultMulticastLoop	bool	true
mecHost2.virtualisationInfrastructure.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.tcp ↗.checksumMode	string	“declared”
mecHost2.virtualisationInfrastructure.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
mecHost2.virtualisationInfrastructure.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
mecHost2.virtualisationInfrastructure.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
mecHost2.virtualisationInfrastructure.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
mecHost2.virtualisationInfrastructure.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
mecHost2.virtualisationInfrastructure.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
mecHost2.virtualisationInfrastructure.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
mecHost2.virtualisationInfrastructure.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
mecHost2.virtualisationInfrastructure.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
mecHost2.virtualisationInfrastructure.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
mecHost2.virtualisationInfrastructure.tcp ↗.msl	int	120s	Maximum Segment Lifetime
mecHost2.virtualisationInfrastructure.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
mecHost2.virtualisationInfrastructure.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
mecHost2.virtualisationInfrastructure.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
mecHost2.virtualisationInfrastructure.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
mecHost2.virtualisationInfrastructure.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost2.virtualisationInfrastructure.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
mecHost2.virtualisationInfrastructure.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
mecHost2.virtualisationInfrastructure.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
mecHost2.virtualisationInfrastructure.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
mecHost2.virtualisationInfrastructure.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.at ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.at ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.tn ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.tn ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.virtualisationInfrastructure.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.virtualisationInfrastructure.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.virtualisationInfrastructure.nl ↗.forwardServiceRegistration	bool	true
mecHost2.virtualisationInfrastructure.nl ↗.forwardProtocolRegistration	bool	true
mecHost2.virtualisationInfrastructure.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.virtualisationInfrastructure.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.virtualisationInfrastructure.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.mecPlatform.serviceRegistry.serviceName	string	“ServiceRegistry”
mecHost2.mecPlatform.serviceRegistry.requestQueueSize	int	0
mecHost2.mecPlatform.serviceRegistry.subscriptionQueueSize	int	0
mecHost2.mecPlatform.serviceRegistry.localAddress	string	“”	Local address; may be left empty (“”)
mecHost2.mecPlatform.serviceRegistry.localPort	int	1000	localPort number to listen on
mecHost2.mecPlatform.serviceRegistry.requestServiceTime	double	15us
mecHost2.mecPlatform.serviceRegistry.subscriptionServiceTime	double	20us
mecHost2.mecPlatform.serviceRegistry.serverThreadClass	string	“simu5g.mec.platform.services.base.SocketManager”
mecHost2.mecPlatform.serviceRegistry.tos	int	-1	If not -1, set the Type of Service (IPv4) / Traffic Class (IPv6) field of sent packets to this value
mecHost2.mecPlatform.serviceRegistry.binderModule	string	“binder”
mecHost2.mecPlatformManager.mecOrchestrator	string
mecHost2.mecPlatformManager.serviceRegistryModule	string	“^.mecPlatform.serviceRegistry”
mecHost2.mecPlatformManager.vimModule	string	“^.vim”
mecHost2.vim.binderModule	string	“binder”
mecHost2.vim.mp1Port	int	10021
mecHost2.vim.scheduling	string	“segregation”
mecHost2.upf_mec.status ↗.displayStringTextFormat	string	“{stateStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.status ↗.initialStatus	string	“UP”	Initial status of the network node
mecHost2.upf_mec.environment ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.environment ↗.initStage	int	0	Initialization stage for the setup command
mecHost2.upf_mec.environment ↗.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
mecHost2.upf_mec.environment ↗.namespace	string	“”	Name of the host OS network namespace (optional) (Linux only)
mecHost2.upf_mec.environment ↗.setupCommand	string	“”	A host OS system command
mecHost2.upf_mec.environment ↗.teardownCommand	string	“”	A host OS system command
mecHost2.upf_mec.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.pcapRecorder ↗.moduleNamePatterns	string	“wlan[] eth[] ppp[*]”	Space-separated list of sibling module names to listen on
mecHost2.upf_mec.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost2.upf_mec.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.cb ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.cb ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.bl ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.bl ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ethernet ↗.displayStringTextFormat	string	“passed up: {totalFromMAC}\nsent: {totalFromHigherLayer}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethernet ↗.registerProtocol	bool	false	FIXME //KLUDGE should redesign place of EthernetEncapsulation and LLC modules
mecHost2.upf_mec.ethernet ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ethernet ↗.fcsMode	string	“declared”
mecHost2.upf_mec.ethernet ↗.stopOperationExtraTime	double	-1s	Extra time after the lifecycle stop operation has finished
mecHost2.upf_mec.ethernet ↗.stopOperationTimeout	double	2s	Timeout value for the lifecycle stop operation
mecHost2.upf_mec.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.li ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.li ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.lo ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.lo ↗.lo ↗.displayStringTextFormat	string	“rcv:{numRcvdOK} snt:{numSent}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.lo ↗.lo ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.lo ↗.lo ↗.mtu	int	4470B
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.wlan ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.wlan ↗.mib ↗.displayStringTextFormat	string	“Address: {address}{ssidStr}\n{modeStr}{stationTypeStr}{qosStr}{associatedStr}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.agent ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.agent ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.wlan ↗.agent ↗.mibModule	string
mecHost2.upf_mec.wlan ↗.agent ↗.activeScan	bool	true	Selects between active and passive scanning
mecHost2.upf_mec.wlan ↗.agent ↗.channelsToScan	string	“”	List of channel numbers to scan (space delimited); empty means all channels
mecHost2.upf_mec.wlan ↗.agent ↗.probeDelay	double	100ms	Delay before sending a probe request during active scanning
mecHost2.upf_mec.wlan ↗.agent ↗.minChannelTime	double	150ms	Min interval to spend on a channel during active scanning
mecHost2.upf_mec.wlan ↗.agent ↗.maxChannelTime	double	300ms	Channel time for passive scanning, and max channel time for active scanning
mecHost2.upf_mec.wlan ↗.agent ↗.authenticationTimeout	double	5s	Timeout for the authentication procedure
mecHost2.upf_mec.wlan ↗.agent ↗.associationTimeout	double	5s	Timeout for the association procedure
mecHost2.upf_mec.wlan ↗.agent ↗.startingTime	double	-1s	Agent starting time.
mecHost2.upf_mec.wlan ↗.agent ↗.defaultSsid	string	“”	List of allowed SSIDs to connect to; leave empty for no filtering
mecHost2.upf_mec.wlan ↗.mgmt ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mgmt ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.wlan ↗.mgmt ↗.numChannels	int	1	Number of channels to scan
mecHost2.upf_mec.wlan ↗.mgmt ↗.mibModule	string
mecHost2.upf_mec.wlan ↗.mgmt ↗.macModule	string		The path to the MAC module
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.originatorMacDataService”
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.inProgressFrames ↗.ackHandlerModule	string	“^.^.ackHandler”
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.channelAccess ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.recoveryProcedure ↗.longRetryLimit	int	4
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorProtectionMechanism ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rxModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.dcf ↗.ctsPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.packetCapacity	int	100	Maximum number of packets in the queue, no limit by default
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.comparatorClass	string	“inet::ieee80211::MgmtOverDataComparator”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.pendingQueue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.displayStringTextFormat	string	“{numInProgress} packets”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.pendingQueueModule	string	“^.pendingQueue”
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.originatorMacDataServiceModule	string	“^.^.^.originatorMacDataService”
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.inProgressFrames ↗.ackHandlerModule	string	“^.ackHandler”
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.displayStringTextFormat	string	“{fsmState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.initialChannelBusy	bool	true	Assume that the channel was busy before the simulation started
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.contention ↗.backoffOptimization	bool	true	We can pretend the frame has arrived into the queue a little bit earlier, and maybe able to start transmitting immediately
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.ackHandler ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.txopProcedure ↗.txopLimit	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.shortRetryLimit	int	7
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.edcaf ↗.recoveryProcedure ↗.longRetryLimit	int	4
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.collisionController ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.shortRetryLimit	int	7
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.edca ↗.mgmtAndNonQoSRecoveryProcedure ↗.longRetryLimit	int	4
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.hcca ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.subframeNumThreshold	int	-1	Minimum number of subframes needed to compose an A-MSDU. (-1 means it won’t be checked)
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.aggregationLengthThreshold	int	-1	The minimum length for an aggregated payload necessary to create an A-MSDU (-1 means it won’t be checked).
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.maxAMsduSize	int	4065	-1 means infinity
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.msduAggregationPolicy ↗.qOsCheck	bool	true	Turns on/off the check of the presence of the QoS flag (false means off – this is needed for aggregation in DCF mode).
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.mpduAggregationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorMacDataService ↗.fragmentationPolicy ↗.fragmentationThreshold	int	1500B
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.singleProtectionMechanism ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.multicastFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseAckFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseBlockAckFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.responseCtsFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBitrate	double	-1bps	Fastest
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameBandwidth	double	nan Hz	Unspecified by default
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.dataFrameNumSpatialStreams	int	-1	Unspecified by default
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.mgmtFrameBitrate	double	-1bps	Fastest
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rateSelection ↗.controlFrameBitrate	double	-1bps
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckReqThreshold	int	5
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.maxBlockAckPolicyFrameLength	int	1000B
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.blockAckTimeout	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorAckPolicy ↗.ackTimeout	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientAckPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.ctsTimeout	double	-1s
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.rtsPolicy ↗.rtsThreshold	int	2346B
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rxModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.ctsPolicy ↗.rateSelectionModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.originatorBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.delayedAckPolicySupported	bool	false
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.aMsduSupported	bool	true
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.maximumAllowedBufferSize	int	64
mecHost2.upf_mec.wlan ↗.mac ↗.hcf ↗.recipientBlockAckAgreementPolicy ↗.blockAckTimeoutValue	double	0s	0 means that it depends on the originator
mecHost2.upf_mec.wlan ↗.mac ↗.ds ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.ds ↗.mibModule	string
mecHost2.upf_mec.wlan ↗.mac ↗.rx ↗.displayStringTextFormat	string	“{rxStatus}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.tx ↗.displayStringTextFormat	string	“{txFramePrefix}{txState}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.wlan ↗.mac ↗.tx ↗.rxModule	string
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.ppp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.ppp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ppp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost2.upf_mec.ppp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.upf_mec.ppp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.ppp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.ppp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.upf_mec.ppp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ppp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ppp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost2.upf_mec.ppp ↗.ppp ↗.mtu	int	4470B
mecHost2.upf_mec.ppp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost2.upf_mec.ppp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.eth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.tun ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.tun ↗.tun ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.tun ↗.tun ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.tun ↗.tun ↗.mtu	int	1500B
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.virt ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.virt ↗.tunnel ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.virt ↗.tunnel ↗.interfaceTableModule	string
mecHost2.upf_mec.virt ↗.tunnel ↗.realInterface	string
mecHost2.upf_mec.virt ↗.tunnel ↗.protocol	string	vlanId != -1 ? “ieee8021qctag” : “”
mecHost2.upf_mec.virt ↗.tunnel ↗.address	string	“copy”
mecHost2.upf_mec.virt ↗.tunnel ↗.vlanId	int	-1
mecHost2.upf_mec.virt ↗.tunnel ↗.steal	bool	vlanId != -1
mecHost2.upf_mec.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.configurator ↗.routingTableModule	string
mecHost2.upf_mec.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
mecHost2.upf_mec.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost2.upf_mec.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
mecHost2.upf_mec.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
mecHost2.upf_mec.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
mecHost2.upf_mec.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.igmp ↗.routingTableModule	string
mecHost2.upf_mec.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
mecHost2.upf_mec.ipv4 ↗.igmp ↗.enabled	bool	true
mecHost2.upf_mec.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
mecHost2.upf_mec.ipv4 ↗.igmp ↗.queryInterval	double	125s
mecHost2.upf_mec.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
mecHost2.upf_mec.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
mecHost2.upf_mec.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
mecHost2.upf_mec.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
mecHost2.upf_mec.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
mecHost2.upf_mec.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
mecHost2.upf_mec.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
mecHost2.upf_mec.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
mecHost2.upf_mec.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.icmp ↗.routingTableModule	string
mecHost2.upf_mec.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
mecHost2.upf_mec.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
mecHost2.upf_mec.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.ip ↗.routingTableModule	string
mecHost2.upf_mec.ipv4 ↗.ip ↗.arpModule	string
mecHost2.upf_mec.ipv4 ↗.ip ↗.icmpModule	string
mecHost2.upf_mec.ipv4 ↗.ip ↗.checksumMode	string	“declared”
mecHost2.upf_mec.ipv4 ↗.ip ↗.timeToLive	int	32
mecHost2.upf_mec.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
mecHost2.upf_mec.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
mecHost2.upf_mec.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
mecHost2.upf_mec.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
mecHost2.upf_mec.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
mecHost2.upf_mec.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
mecHost2.upf_mec.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
mecHost2.upf_mec.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv4 ↗.arp ↗.routingTableModule	string
mecHost2.upf_mec.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
mecHost2.upf_mec.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
mecHost2.upf_mec.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
mecHost2.upf_mec.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.interfaceTableModule	string
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.spdConfig	xml
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost2.upf_mec.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost2.upf_mec.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.configurator ↗.interfaceTableModule	string
mecHost2.upf_mec.ipv6 ↗.configurator ↗.routingTableModule	string
mecHost2.upf_mec.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
mecHost2.upf_mec.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.forwarding	bool	false
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
mecHost2.upf_mec.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
mecHost2.upf_mec.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
mecHost2.upf_mec.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
mecHost2.upf_mec.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
mecHost2.upf_mec.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.routingTableModule	string
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.icmpv6Module	string
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.procDelay	double	0s
mecHost2.upf_mec.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.interfaceTableModule	string
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.spdConfig	xml
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
mecHost2.upf_mec.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
mecHost2.upf_mec.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.isMobileNode	bool
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
mecHost2.upf_mec.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
mecHost2.upf_mec.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
mecHost2.upf_mec.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
mecHost2.upf_mec.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
mecHost2.upf_mec.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
mecHost2.upf_mec.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
mecHost2.upf_mec.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
mecHost2.upf_mec.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
mecHost2.upf_mec.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
mecHost2.upf_mec.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
mecHost2.upf_mec.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
mecHost2.upf_mec.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
mecHost2.upf_mec.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
mecHost2.upf_mec.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
mecHost2.upf_mec.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
mecHost2.upf_mec.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
mecHost2.upf_mec.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.nl ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.nl ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.udp ↗.checksumMode	string	“declared”
mecHost2.upf_mec.udp ↗.defaultMulticastLoop	bool	true
mecHost2.upf_mec.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.tcp ↗.checksumMode	string	“declared”
mecHost2.upf_mec.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
mecHost2.upf_mec.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
mecHost2.upf_mec.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
mecHost2.upf_mec.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
mecHost2.upf_mec.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
mecHost2.upf_mec.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
mecHost2.upf_mec.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
mecHost2.upf_mec.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
mecHost2.upf_mec.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
mecHost2.upf_mec.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
mecHost2.upf_mec.tcp ↗.msl	int	120s	Maximum Segment Lifetime
mecHost2.upf_mec.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
mecHost2.upf_mec.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
mecHost2.upf_mec.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
mecHost2.upf_mec.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
mecHost2.upf_mec.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost2.upf_mec.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
mecHost2.upf_mec.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
mecHost2.upf_mec.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
mecHost2.upf_mec.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
mecHost2.upf_mec.sctp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.sctp ↗.interfaceTableModule	string
mecHost2.upf_mec.sctp ↗.routingTableModule	string
mecHost2.upf_mec.sctp ↗.checksumMode	string	“declared”
mecHost2.upf_mec.sctp ↗.numGapReports	int	3
mecHost2.upf_mec.sctp ↗.rtoInitial	double	3s
mecHost2.upf_mec.sctp ↗.rtoMin	double	1s
mecHost2.upf_mec.sctp ↗.rtoMax	double	60s
mecHost2.upf_mec.sctp ↗.rtoAlpha	double	0.125
mecHost2.upf_mec.sctp ↗.rtoBeta	double	0.250
mecHost2.upf_mec.sctp ↗.maxBurst	int	4
mecHost2.upf_mec.sctp ↗.maxBurstVariant	string	“maxBurst”
mecHost2.upf_mec.sctp ↗.initialWindow	int	0
mecHost2.upf_mec.sctp ↗.assocMaxRetrans	int	10
mecHost2.upf_mec.sctp ↗.pathMaxRetrans	int	5
mecHost2.upf_mec.sctp ↗.maxInitRetrans	int	8
mecHost2.upf_mec.sctp ↗.sackPeriod	double	200ms
mecHost2.upf_mec.sctp ↗.sackFrequency	int	2
mecHost2.upf_mec.sctp ↗.reactivatePrimaryPath	bool	false
mecHost2.upf_mec.sctp ↗.sendQueueLimit	int	0
mecHost2.upf_mec.sctp ↗.validCookieLifetime	double	10s
mecHost2.upf_mec.sctp ↗.enableHeartbeats	bool	true
mecHost2.upf_mec.sctp ↗.hbInterval	double	30s
mecHost2.upf_mec.sctp ↗.sendHeartbeatsOnActivePaths	bool	false
mecHost2.upf_mec.sctp ↗.nagleEnabled	bool	true
mecHost2.upf_mec.sctp ↗.naglePoint	int	1468
mecHost2.upf_mec.sctp ↗.fragPoint	int	1452	Size of a message that has to be fragmented, i.e. maximum size of a fragment
mecHost2.upf_mec.sctp ↗.fastRecoverySupported	bool	true
mecHost2.upf_mec.sctp ↗.sctpAlgorithmClass	string	“SctpAlg”
mecHost2.upf_mec.sctp ↗.ccModule	int	0	RFC4960=0
mecHost2.upf_mec.sctp ↗.osbWithHeader	bool	false
mecHost2.upf_mec.sctp ↗.RTXMethod	int	0	0=Once after 3 Sacks; 1=once per RTT; 2=Switch off Fast Retransmit; 3=Always after 3 Sacks
mecHost2.upf_mec.sctp ↗.ssModule	int	0	ROUND_ROBIN=0
mecHost2.upf_mec.sctp ↗.arwnd	int	65535
mecHost2.upf_mec.sctp ↗.swsLimit	int	3000	Limit for SWS
mecHost2.upf_mec.sctp ↗.udpEncapsEnabled	bool	false
mecHost2.upf_mec.sctp ↗.natFriendly	bool	false
mecHost2.upf_mec.sctp ↗.bytesToAddPerRcvdChunk	int	0	For flow control
mecHost2.upf_mec.sctp ↗.bytesToAddPerPeerChunk	int	0	For flow control
mecHost2.upf_mec.sctp ↗.tellArwnd	bool	false	For flow control
mecHost2.upf_mec.sctp ↗.messageAcceptLimit	int	0	For flow control
mecHost2.upf_mec.sctp ↗.fairStart	double	0s
mecHost2.upf_mec.sctp ↗.fairStop	double	0s
mecHost2.upf_mec.sctp ↗.streamsToPaths	string	“”
mecHost2.upf_mec.sctp ↗.startEndToEndDelay	int	0
mecHost2.upf_mec.sctp ↗.stopEndToEndDelay	int	10
mecHost2.upf_mec.sctp ↗.throughputInterval	double	1
mecHost2.upf_mec.sctp ↗.auth	bool	false
mecHost2.upf_mec.sctp ↗.chunks	string	“”
mecHost2.upf_mec.sctp ↗.padding	bool	false
mecHost2.upf_mec.sctp ↗.addIP	bool	false
mecHost2.upf_mec.sctp ↗.addTime	double	0s
mecHost2.upf_mec.sctp ↗.addAddress	string	“”
mecHost2.upf_mec.sctp ↗.addIpType	string	“0”	SET_PRIMARY_ADDRESS=49156,ADD_IP_ADDRESS=49153,DELETE_IP_ADDRESS=49154
mecHost2.upf_mec.sctp ↗.packetDrop	bool	false
mecHost2.upf_mec.sctp ↗.sackNow	bool	false
mecHost2.upf_mec.sctp ↗.highSpeedCC	bool	false
mecHost2.upf_mec.sctp ↗.checkSackSeqNumber	bool	false
mecHost2.upf_mec.sctp ↗.nrSack	bool	false
mecHost2.upf_mec.sctp ↗.disableReneging	bool	false
mecHost2.upf_mec.sctp ↗.gapReportLimit	int	100000000
mecHost2.upf_mec.sctp ↗.gapListOptimizationVariant	string	“none”
mecHost2.upf_mec.sctp ↗.smartOverfullSACKHandling	bool	false
mecHost2.upf_mec.sctp ↗.allowQoSTracking	bool	false
mecHost2.upf_mec.sctp ↗.qosTrackingInterval	double	1.0s
mecHost2.upf_mec.sctp ↗.cmtSendAllVariant	string	“normal”
mecHost2.upf_mec.sctp ↗.cmtRetransmissionVariant	string	“normal”
mecHost2.upf_mec.sctp ↗.cmtCUCVariant	string	“normal”
mecHost2.upf_mec.sctp ↗.cmtBufferSplitVariant	string	“none”
mecHost2.upf_mec.sctp ↗.cmtBufferSplittingUsesOSB	bool	false
mecHost2.upf_mec.sctp ↗.cmtUseSFR	bool	true
mecHost2.upf_mec.sctp ↗.cmtUseDAC	bool	true
mecHost2.upf_mec.sctp ↗.cmtUseFRC	bool	true
mecHost2.upf_mec.sctp ↗.cmtSmartT3Reset	bool	true
mecHost2.upf_mec.sctp ↗.cmtSmartFastRTX	bool	true
mecHost2.upf_mec.sctp ↗.cmtSmartReneging	bool	false
mecHost2.upf_mec.sctp ↗.cmtSlowPathRTTUpdate	bool	false
mecHost2.upf_mec.sctp ↗.cmtChunkReschedulingVariant	string	“none”
mecHost2.upf_mec.sctp ↗.cmtChunkReschedulingThreshold	double	0.5
mecHost2.upf_mec.sctp ↗.cmtMovedChunksReduceCwnd	bool	true
mecHost2.upf_mec.sctp ↗.movedChunkFastRTXFactor	double	2.0
mecHost2.upf_mec.sctp ↗.cmtSackPath	string	“standard”
mecHost2.upf_mec.sctp ↗.strictCwndBooking	bool	false
mecHost2.upf_mec.sctp ↗.cmtCCVariant	string	“off”	CMT Congestion Control Variant off = use over every path the default RFC4960 CC (New Reno) lia = First resource pooling congestion control RFC6356 adapted for SCTP - https://datatracker.ietf.org/doc/rfc6356/ olia = alternative MPTCP CC, adapted for SCTP- https://tools.ietf.org/html/draft-khalili-mptcp-congestion-control-05 cmtrpv1 = First resource pooling based CC for SCTP - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/AINA2010.pdf cmtrpv2 = Updated version of cmtrpv1 - https://www.tdr.wiwi.uni-due.de/fileadmin/fileupload/I-TDR/SCTP/Paper/ConTEL2011.pdf
mecHost2.upf_mec.sctp ↗.cmtCCPathGroups	string	“”
mecHost2.upf_mec.sctp ↗.rpPathBlocking	bool	false
mecHost2.upf_mec.sctp ↗.rpScaleBlockingTimeout	bool	false
mecHost2.upf_mec.sctp ↗.rpMinCwnd	int	1
mecHost2.upf_mec.quic ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.quic ↗.routingTableModule	string		Set by StandardHost.
mecHost2.upf_mec.quic ↗.sendZeroRttTokenAsServer	bool	false
mecHost2.upf_mec.quic ↗.congestionControl	string	“NewReno”	Sets the congestion control algorithm (NewReno or No).
mecHost2.upf_mec.quic ↗.accurateIncreaseInNewRenoCongestionAvoidance	bool	true	For NewReno in Congestion Avoidance, if true, increases cwnd after cwnd-acked bytes; if false, increases cwnd on every acked packet by acked_bytes/cwnd.
mecHost2.upf_mec.quic ↗.sendQueueLimit	int	64MB	Sets the limit of the send queue in bytes.
mecHost2.upf_mec.quic ↗.sendQueueLowWaterRatio	double	.4	Defines the send queue low water mark relative to the limit.
mecHost2.upf_mec.quic ↗.initialMaxData	int	15MB	Connection level flow control credit. Used as own and peer’s value.
mecHost2.upf_mec.quic ↗.initialMaxStreamData	int	6MB	Stream level flow control credit for any stream (unidirectional, bidirectional local and remote). Used as own and peer’s value.
mecHost2.upf_mec.quic ↗.maxDataFrameThreshold	double	0.5*initialMaxData	Defines when MaxDataFrame in ConnectionFlowControl will be send.
mecHost2.upf_mec.quic ↗.maxStreamDataFrameThreshold	double	0.5*initialMaxStreamData	Defines when MaxStreamDataFrame in StreamFlowControl will be send.
mecHost2.upf_mec.quic ↗.roundConsumedDataValue	bool	false	If true, FlowControlResponder rounds consumedData in streamRcvBuffer to the next packetSize.
mecHost2.upf_mec.quic ↗.sendMaxDataFramesImmediately	bool	false	If true, a MAX_(STREAM)_DATA frame is sent immediately, after generation. Otherwise, sending the frame is delayed until the sending process starts due to another event.
mecHost2.upf_mec.quic ↗.bundleAckForNonAckElicitingPackets	bool	false	If true, bundles ack for non-ack-eliciting packets in an outgoing packet.
mecHost2.upf_mec.quic ↗.numReceivedAckElicitingsBeforeAck	int	2	Number of ack eliciting packets a receiver waits for, before it sends an ACK, immediately.
mecHost2.upf_mec.quic ↗.useIBit	bool	false	If true, an ACK frame is sent immediately upon an ack-eliciting packet with the I-Bit set.
mecHost2.upf_mec.quic ↗.useDplpmtud	bool	false	If true, uses DPLPMTUD (RFC8899) to determine the PMTU.
mecHost2.upf_mec.quic ↗.maxPmtu	int	65535B	With useDplpmtud, it is used as upper limit for the PMTU search. Without useDplpmtud, the PMTU is set to the minimum of the MTU of the outgoing interface and this value.
mecHost2.upf_mec.quic ↗.dplpmtudMinPmtu	int	0	Specifies the minimum PMTU to use (if 0, it uses 1200 B for IPv4 or 1280 B for IPv6 as minimum PMTU).
mecHost2.upf_mec.quic ↗.dplpmtudMaxProbes	int	3	Specifies the number of probe packet sent for one candidate before given up.
mecHost2.upf_mec.quic ↗.dplpmtudUsePtb	bool	true	If true, uses ICMP Packet Too Big (PTB) messages for DPLPMTUD.
mecHost2.upf_mec.quic ↗.dplpmtudCandidateSequence	string	“OptBinary”	Specifies the sequence of candidates used for the search algorithm of DPLPMTUD (Up, Down, OptUp, Binary, OptBinary, Jump).
mecHost2.upf_mec.quic ↗.skipPacketNumberForDplpmtudProbePackets	bool	false	Specifies whether to skip a packet number for a DPLPMTUD probe packet in order to avoid ack delay.
mecHost2.upf_mec.quic ↗.useCwndForParallelProbes	int	0	If 0, no parallel probe packets; if 1, uses the availbale cwnd to send additional probe packets and if 2 prefers to send probe packets over other packets.
mecHost2.upf_mec.quic ↗.sendDataDuringInitalDplpmtudBase	bool	true	If false, waits for DPLPMTUD switching initially to SEARCH before start sending application data.
mecHost2.upf_mec.quic ↗.dplpmtudUsePmtuValidator	bool	true	If true, activates the PMTU Validator that trys to detect when the current PMTU estimation is larger than the actual PMTU.
mecHost2.upf_mec.quic ↗.pmtuValidatorLostPacketsThreshold	int	2	Specifies the number of lost data packets before assuming a decreased PMTU.
mecHost2.upf_mec.quic ↗.pmtuValidatorTimeThreshold	double	-1s	Specifies the time threshold between two lost packets. If negative, pmtuValidatorSrttFactorThreshold is used instead.
mecHost2.upf_mec.quic ↗.pmtuValidatorSrttFactorThreshold	int	1	If pmtuValidatorTimeThreshold is negative, this number multiplied by SRTT is used instead.
mecHost2.upf_mec.quic ↗.pmtuValidatorInvalidOnPersistentCongestion	int	1	If 0, disabled. If 1, the PMTU validator uses persistent congeation as signal for a decreased PMTU. If 2, only two consecutive persisten congestions used as signal. If 3, …
mecHost2.upf_mec.quic ↗.reducePacketTimeThreshold	double	0s	Specifies after which time with no acks, packets with reduced size are sent. If zero, packet size reduction is disabled. If negative, reducePacketPtoFactorThreshold is used instead.
mecHost2.upf_mec.quic ↗.reducePacketPtoFactorThreshold	int	3	If reducePacketTimeThreshold is negative, this number multiplied by PTO is used instead.
mecHost2.upf_mec.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.tn ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.tn ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.at ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.at ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.dnPpp ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.dnPpp ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnPpp ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
mecHost2.upf_mec.dnPpp ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.upf_mec.dnPpp ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.dnPpp ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.dnPpp ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.upf_mec.dnPpp ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnPpp ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
mecHost2.upf_mec.dnPpp ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
mecHost2.upf_mec.dnPpp ↗.ppp ↗.mtu	int	4470B
mecHost2.upf_mec.dnPpp ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
mecHost2.upf_mec.dnPpp ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
mecHost2.upf_mec.relay.trafficFlowFilter.binderModule	string	“binder”
mecHost2.upf_mec.relay.trafficFlowFilter.fastForwarding	bool	true
mecHost2.upf_mec.relay.gtpUser.binderModule	string	“binder”
mecHost2.upf_mec.relay.gtpUser.localPort	int	31
mecHost2.upf_mec.relay.gtpUser.tunnelPeerPort	int	31
mecHost2.upf_mec.rd ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.rd ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.rd ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.nodeControl.binderModule	string	“binder”
mecHost2.upf_mec.nodeControl.gtpUserModule	string	“^.relay.gtpUser”
mecHost2.upf_mec.nodeControl.trafficFlowFilterModule	string	“^.relay.trafficFlowFilter”
mecHost2.upf_mec.nodeControl.ethernetBridgeModule	string	“^.ethBridge.sessionMux”	The node’s Ethernet session bridge (see EthernetSessionBridge), if it has one
mecHost2.upf_mec.nodeControl.unstructuredPrefix	string	“”	The prefix the N6 addresses of Unstructured sessions are allocated from, e.g. “2001:db8:5::/64” or “10.5.0.0/16”; empty = the node anchors no Unstructured session (see the main comment)
mecHost2.upf_mec.nodeControl.unstructuredServer	string	“”	The application server the Unstructured sessions’ uplink goes to: a module path relative to the network, resolved in the family of unstructuredPrefix
mecHost2.upf_mec.nodeControl.unstructuredServerPort	int	-1	The UDP port of unstructuredServer the uplink goes to; must be set for Unstructured sessions
mecHost2.upf_mec.nodeControl.unstructuredPort	int	-1	The UDP port the node receives the Unstructured sessions’ downlink on, and sends their uplink from; must be set for Unstructured sessions
mecHost2.upf_mec.ndResponder.binderModule	string	“binder”
mecHost2.upf_mec.ndResponder.linkLocalAddress	string	“fe80::1”	The router’s address on every session’s link
mecHost2.upf_mec.ndResponder.routerLifetime	double	9000s	Router Lifetime in the Router Advertisements (max 9000s, RFC 4861)
mecHost2.upf_mec.ndResponder.curHopLimit	int	64	Cur Hop Limit in the Router Advertisements (0 = unspecified)
mecHost2.upf_mec.ndResponder.checksumMode	string	“declared”
mecHost2.upf_mec.ethBridge.macTable ↗.displayStringTextFormat	string	“addr: %a\nvlan: %v”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.macTable ↗.agingTime	double	120s
mecHost2.upf_mec.ethBridge.macTable ↗.forwardingTable	object	[]
mecHost2.upf_mec.ethBridge.macTable ↗.forwardingTableFile	string	“”
mecHost2.upf_mec.ethBridge.macTable ↗.interfaceTableModule	string
mecHost2.upf_mec.ethBridge.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
mecHost2.upf_mec.ethBridge.sessionMux.interfaceTableModule	string		The bridge’s interface table, which the session ports are registered in
mecHost2.upf_mec.ethBridge.sessionMux.macTableModule	string		The bridge’s MAC table, flushed of a released session’s port
mecHost2.upf_mec.ethBridge.sessionMux.portModuleType	string	“simu5g.corenetwork.ethernetSessionBridge.EthernetSessionPort”	The module type of the session ports
mecHost2.upf_mec.ethBridge.sessionMux.portDisplayString	string	“p=500,420,row,100;g=sessionPorts”	Display string of the session ports (their place in the bridge’s layout)
mecHost2.upf_mec.ethBridge.cb ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.cb ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ethBridge.cb ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ethBridge.cb ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ethBridge.cb ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ethBridge.cb ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ethBridge.cb ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.fork ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardVlan	bool	true
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.forwardPcp	bool	true
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.reverser ↗.excludeEncapsulationProtocols	object	[]
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.join ↗.displayStringTextFormat	string	“passed %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bridging ↗.directionReverser ↗.join ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.macTableModule	string		Relative module path of MAC table
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.learner ↗.interfaceTableModule	string		Relative module path of the interface table
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.macTableModule	string		Relative module path of MAC table
mecHost2.upf_mec.ethBridge.bridging ↗.interfaceRelay ↗.selector ↗.interfaceTableModule	string		Relative module path of interface table
mecHost2.upf_mec.ethBridge.bl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.bl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ethBridge.bl ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ethBridge.bl ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ethBridge.bl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ethBridge.bl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ethBridge.bl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.ethBridge.ethernet ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.socketCommandProcessor ↗.socketTableModule	string
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderInserter ↗.interfaceTableModule	string
mecHost2.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.minLength	int
mecHost2.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.roundingLength	int	1B
mecHost2.upf_mec.ethBridge.ethernet ↗.paddingInserter ↗.insertionPosition	string	“back”
mecHost2.upf_mec.ethBridge.ethernet ↗.fcsInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.fcsInserter ↗.fcsMode	string	“declared”
mecHost2.upf_mec.ethBridge.ethernet ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.socketPacketProcessor ↗.socketTableModule	string
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.backpressure	bool	false
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.interfaceTableModule	string
mecHost2.upf_mec.ethBridge.ethernet ↗.macHeaderChecker ↗.promiscuous	bool	false
mecHost2.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.backpressure	bool	false
mecHost2.upf_mec.ethBridge.ethernet ↗.fcsChecker ↗.popFcs	bool	true
mecHost2.upf_mec.ethBridge.ieee8021q ↗.socketTable ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ieee8021q ↗.socketCommandProcessor ↗.socketTableModule	string
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.vlanTagType	string	“c”
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.nextProtocol	string	“ethernetmac”
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultVlanId	int	-1
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultPcp	int	-1
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultUserPriority	int	-1
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderInserter ↗.defaultDropEligible	int	-1	<0: unspecified, 0: false, >0: true
mecHost2.upf_mec.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ieee8021q ↗.socketPacketProcessor ↗.socketTableModule	string
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.backpressure	bool	false
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanTagType	string	“c”
mecHost2.upf_mec.ethBridge.ieee8021q ↗.qTagHeaderChecker ↗.vlanIdFilter	object	[]
mecHost2.upf_mec.ethBridge.li ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.ethBridge.li ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
mecHost2.upf_mec.ethBridge.li ↗.forwardServiceRegistration	bool	true
mecHost2.upf_mec.ethBridge.li ↗.forwardProtocolRegistration	bool	true
mecHost2.upf_mec.ethBridge.li ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
mecHost2.upf_mec.ethBridge.li ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
mecHost2.upf_mec.ethBridge.li ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
mecHost2.upf_mec.dnEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.packetCapacity	int	-1	Maximum number of packets in the queue, no limit by default
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.dropperClass	string	“”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
mecHost2.upf_mec.dnEth ↗.macLayer ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
mecHost2.upf_mec.dnEth ↗.macLayer ↗.server ↗.displayStringTextFormat	string	“served %p pk (%l)”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.macLayer ↗.server ↗.serveSchedulingPriority	int	0	Specifies the FES scheduling priority for the extra event that is pulling the packet, -1 means no extra event
mecHost2.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.direction	string	“undefined”
mecHost2.upf_mec.dnEth ↗.macLayer ↗.outboundEmitter ↗.signalName	string
mecHost2.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.backpressure	bool	false
mecHost2.upf_mec.dnEth ↗.macLayer ↗.fcsChecker ↗.popFcs	bool	false
mecHost2.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.direction	string	“undefined”
mecHost2.upf_mec.dnEth ↗.macLayer ↗.inboundEmitter ↗.signalName	string
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderInserter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.displayStringTextFormat	string	“delayed %p pk (%l)\nifg: %g”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.initialChannelBusy	bool	false	Assume that the channel was busy before the simulation started
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.interFrameGapInserter ↗.duration	double	96s / dropUnit(parent.bitrate)
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.direction	string	“undefined”
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.outboundEmitter ↗.signalName	string
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.clockModule	string	“”	Relative path of a module that implements IClock; optional
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.transmitter ↗.datarate	double	parent.bitrate
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.displayStringTextFormat	string	“dropped {numDroppedPackets}/{numProcessedPackets} pk ({droppedTotalLength}/{processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.phyHeaderChecker ↗.backpressure	bool	false
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.direction	string	“undefined”
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.inboundEmitter ↗.signalName	string
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.receiver ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
mecHost2.upf_mec.dnEth ↗.phyLayer ↗.receiver ↗.datarate	double	parent.bitrate
mecOrchestrator.binderModule	string	“binder”
mecOrchestrator.selectionPolicy	string	“MecServiceBased”	Available policies: “MecHostBased”, “MecServiceBased”, “AvailableResourcesBased”
mecOrchestrator.mecHostIndex	int	0	To be used with the MecHostBased policy
mecOrchestrator.mecHostList	object	[]
mecOrchestrator.mecApplicationPackageList	object	[]
mecOrchestrator.onboardingTime	double	50ms	Times to simulate lifecycle operations
mecOrchestrator.instantiationTime	double	50ms
mecOrchestrator.terminationTime	double	50ms
ualcmp.interfaceTable ↗.displayStringTextFormat	string	“{numInterfaces} interfaces”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.interfaceTable ↗.displayAddresses	bool	false	Whether to display IP addresses on links
ualcmp.pppIf ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.pppIf ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ualcmp.pppIf ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ualcmp.pppIf ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ualcmp.pppIf ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ualcmp.pppIf ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ualcmp.pppIf ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ualcmp.pppIf ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ualcmp.pppIf ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ualcmp.pppIf ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ualcmp.pppIf ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ualcmp.pppIf ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ualcmp.pppIf ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ualcmp.pppIf ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ualcmp.pppIf ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ualcmp.pppIf ↗.queue ↗.displayStringTextFormat	string	“contains %p pk (%l) pushed %u\npulled %o removed %r dropped %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.pppIf ↗.queue ↗.packetCapacity	int	10000	Maximum number of packets in the queue, no limit by default
ualcmp.pppIf ↗.queue ↗.dataCapacity	int	-1b	Maximum total length of packets in the queue, no limit by default
ualcmp.pppIf ↗.queue ↗.dropperClass	string	“inet::queueing::PacketAtCollectionEndDropper”	Determines which packets are dropped when the queue is overloaded, packets are not dropped by default; the parameter must be the name of a C++ class which implements the IPacketDropperFunction C++ interface and is registered via Register_Class
ualcmp.pppIf ↗.queue ↗.comparatorClass	string	“”	Determines the order of packets in the queue, insertion order by default; the parameter must be the name of a C++ class which implements the IPacketComparatorFunction C++ interface and is registered via Register_Class
ualcmp.pppIf ↗.queue ↗.bufferModule	string	“”	Relative module path to the IPacketBuffer module used by this queue, implicit buffer by default
ualcmp.pppIf ↗.ppp ↗.displayStringTextFormat	string	“rate: %b\nsent: %s, rcvd: %r\nqueue: %q, drop: %d”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.pppIf ↗.ppp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.pppIf ↗.ppp ↗.sendRawBytes	bool	false	When true packets are serialized into a sequence of bytes before sending out
ualcmp.pppIf ↗.ppp ↗.mtu	int	4470B
ualcmp.pppIf ↗.ppp ↗.stopOperationExtraTime	double	-1s	Extra time after lifecycle stop operation finished
ualcmp.pppIf ↗.ppp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
ualcmp.extEth ↗.pcapRecorder ↗.displayStringTextFormat	string	“rec: %n pks”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.extEth ↗.pcapRecorder ↗.verbose	bool	true	Whether to log packets on the module output
ualcmp.extEth ↗.pcapRecorder ↗.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
ualcmp.extEth ↗.pcapRecorder ↗.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
ualcmp.extEth ↗.pcapRecorder ↗.pcapFile	string	“”	The PCAP file to be written, suggested value: pcapFile = “${resultdir}/${configname}-#${runnumber}” + fullpath() + “.pcap”
ualcmp.extEth ↗.pcapRecorder ↗.fileFormat	string	“pcapng”
ualcmp.extEth ↗.pcapRecorder ↗.snaplen	int	65535	Maximum number of bytes to record per packet
ualcmp.extEth ↗.pcapRecorder ↗.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see ‘if_tsresol’ option in pcapng file format).
ualcmp.extEth ↗.pcapRecorder ↗.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
ualcmp.extEth ↗.pcapRecorder ↗.sendingSignalNames	string	“transmissionEnded”	Space-separated list of outbound packet signals to subscribe to
ualcmp.extEth ↗.pcapRecorder ↗.receivingSignalNames	string	“receptionEnded”	Space-separated list of inbound packet signals to subscribe to
ualcmp.extEth ↗.pcapRecorder ↗.dumpProtocols	string	“ethernetmac ppp ieee80211mac”	Space-separated list of protocol names as defined in the Protocol class
ualcmp.extEth ↗.pcapRecorder ↗.packetFilter	object	“*”	Which packets are considered, matches all packets by default
ualcmp.extEth ↗.pcapRecorder ↗.helpers	string	“”	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype
ualcmp.extEth ↗.pcapRecorder ↗.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
ualcmp.extEth ↗.socket ↗.displayStringTextFormat	string	“device: {device}\nsnt:{numSent} rcv:{numReceived}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.extEth ↗.socket ↗.device	string		Name of an existing real Ethernet device
ualcmp.extEth ↗.socket ↗.namespace	string	“”
ualcmp.extEth ↗.socket ↗.packetNameFormat	string	“Ext-%p-%t-%n”	Name of received packets
ualcmp.ipv4 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.configurator ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.configurator ↗.routingTableModule	string
ualcmp.ipv4 ↗.configurator ↗.networkConfiguratorModule	string	“configurator”	The absolute path to the Ipv4NetworkConfigurator; use “” if there is no configurator
ualcmp.ipv4 ↗.configurator ↗.configureRoutingTable	bool	true	Add routing entries to the routing table (uses the configurator module)
ualcmp.ipv4 ↗.routingTable ↗.displayStringTextFormat	string	“{routingTableStatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.routingTable ↗.routerId	string	“auto”	For routers, the router id using IPv4 address dotted
ualcmp.ipv4 ↗.routingTable ↗.netmaskRoutes	string	“*”	Maintain netmask routes for interfaces
ualcmp.ipv4 ↗.routingTable ↗.forwarding	bool	true	Turns IP forwarding on/off
ualcmp.ipv4 ↗.routingTable ↗.multicastForwarding	bool	false	Turns multicast forwarding on/off
ualcmp.ipv4 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
ualcmp.ipv4 ↗.routingTable ↗.routingFile	string	“”	Routing table file name
ualcmp.ipv4 ↗.natTable ↗.displayStringTextFormat	string	“{numNatEntries} entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.natTable ↗.networkProtocolModule	string	“^.ip”
ualcmp.ipv4 ↗.natTable ↗.config	xml	xml(“<config></config>”)	XML configuration parameters for network address translation
ualcmp.ipv4 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.ipv4 ↗.up ↗.forwardServiceRegistration	bool	true
ualcmp.ipv4 ↗.up ↗.forwardProtocolRegistration	bool	true
ualcmp.ipv4 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.ipv4 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.ipv4 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.ipv4 ↗.igmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.igmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.igmp ↗.routingTableModule	string
ualcmp.ipv4 ↗.igmp ↗.checksumMode	string	“declared”
ualcmp.ipv4 ↗.igmp ↗.enabled	bool	true
ualcmp.ipv4 ↗.igmp ↗.robustnessVariable	int	2	IGMP is robust to (robustnessVariable-1) packet loss
ualcmp.ipv4 ↗.igmp ↗.queryInterval	double	125s
ualcmp.ipv4 ↗.igmp ↗.queryResponseInterval	double	10s
ualcmp.ipv4 ↗.igmp ↗.groupMembershipInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval
ualcmp.ipv4 ↗.igmp ↗.otherQuerierPresentInterval	double	(robustnessVariable * queryInterval) + (queryResponseInterval / 2)
ualcmp.ipv4 ↗.igmp ↗.startupQueryInterval	double	queryInterval / 4
ualcmp.ipv4 ↗.igmp ↗.startupQueryCount	int	robustnessVariable
ualcmp.ipv4 ↗.igmp ↗.lastMemberQueryInterval	double	1s
ualcmp.ipv4 ↗.igmp ↗.lastMemberQueryCount	int	robustnessVariable
ualcmp.ipv4 ↗.igmp ↗.unsolicitedReportInterval	double	10s
ualcmp.ipv4 ↗.icmp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.icmp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.icmp ↗.routingTableModule	string
ualcmp.ipv4 ↗.icmp ↗.checksumMode	string	“declared”
ualcmp.ipv4 ↗.icmp ↗.quoteLength	int	8B	Number of bytes from original packet to quote in ICMP reply
ualcmp.ipv4 ↗.mp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.mp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.ipv4 ↗.mp ↗.forwardServiceRegistration	bool	true
ualcmp.ipv4 ↗.mp ↗.forwardProtocolRegistration	bool	true
ualcmp.ipv4 ↗.mp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.ipv4 ↗.mp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.ipv4 ↗.mp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.ipv4 ↗.ip ↗.displayStringTextFormat	string	“{ipv4StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.ip ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.ip ↗.routingTableModule	string
ualcmp.ipv4 ↗.ip ↗.arpModule	string
ualcmp.ipv4 ↗.ip ↗.icmpModule	string
ualcmp.ipv4 ↗.ip ↗.checksumMode	string	“declared”
ualcmp.ipv4 ↗.ip ↗.timeToLive	int	32
ualcmp.ipv4 ↗.ip ↗.multicastTimeToLive	int	32
ualcmp.ipv4 ↗.ip ↗.fragmentTimeout	double	60s
ualcmp.ipv4 ↗.ip ↗.limitedBroadcast	bool	false	Send out limited broadcast packets coming from the higher layer
ualcmp.ipv4 ↗.ip ↗.directBroadcastInterfaces	string	“”	List of interfaces where direct broadcast is enabled (by default direct broadcast is disabled on all interfaces)
ualcmp.ipv4 ↗.ip ↗.enableLocalOutMulticastRouting	bool	false	Enable using the multicast routing table for determining outgoing interfaces for local out packets
ualcmp.ipv4 ↗.ip ↗.enableTimestampOption	bool	false	When enabled, IP inserts a timestamp option into the IP header
ualcmp.ipv4 ↗.ip ↗.maxLifetime	double	-1s	Packets older than the limit are discarded
ualcmp.ipv4 ↗.arp ↗.displayStringTextFormat	string	“size:{arpCacheSize} sent:{numRequestsSent}\nrepl:{numRepliesSent} fail:{numFailedResolutions}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.arp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv4 ↗.arp ↗.routingTableModule	string
ualcmp.ipv4 ↗.arp ↗.retryTimeout	double	1s	Number of seconds ARP waits between retries to resolve an IPv4 address
ualcmp.ipv4 ↗.arp ↗.retryCount	int	3	Number of times ARP will attempt to resolve an IPv4 address
ualcmp.ipv4 ↗.arp ↗.cacheTimeout	double	120s	Number of seconds unused entries in the cache will time out
ualcmp.ipv4 ↗.arp ↗.proxyArpInterfaces	string	“*”	List of interfaces that proxy ARP is enabled on (all interfaces by default)
ualcmp.ipv4 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.ipsec ↗.networkProtocolModule	string	“^.ip”
ualcmp.ipv4 ↗.ipsec ↗.networkProtocol	string	“ipv4”	address family this instance protects (set to “ipv6” in Ipv6NetworkLayer)
ualcmp.ipv4 ↗.ipsec ↗.interfaceTableModule	string
ualcmp.ipv4 ↗.ipsec ↗.spdModule	string	“^.spd”
ualcmp.ipv4 ↗.ipsec ↗.sadModule	string	“^.sad”
ualcmp.ipv4 ↗.ipsec ↗.spdConfig	xml
ualcmp.ipv4 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
ualcmp.ipv4 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
ualcmp.ipv4 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
ualcmp.ipv4 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
ualcmp.ipv4 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
ualcmp.ipv4 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
ualcmp.ipv4 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
ualcmp.ipv4 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
ualcmp.ipv4 ↗.ipsec ↗.espProtectInDelay	double	0.0s
ualcmp.ipv4 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv4 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.ipv4 ↗.lp ↗.forwardServiceRegistration	bool	true
ualcmp.ipv4 ↗.lp ↗.forwardProtocolRegistration	bool	true
ualcmp.ipv4 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.ipv4 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.ipv4 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.ipv6 ↗.configurator ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.configurator ↗.interfaceTableModule	string
ualcmp.ipv6 ↗.configurator ↗.routingTableModule	string
ualcmp.ipv6 ↗.configurator ↗.networkConfiguratorModule	string	“”	The absolute path to the Ipv6NetworkConfigurator; use “” if there is no configurator
ualcmp.ipv6 ↗.configurator ↗.configureRoutingTable	bool	true
ualcmp.ipv6 ↗.routingTable ↗.displayStringTextFormat	string	“{numRoutes} routes\n{numDestCache} destcache entries”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.routingTable ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv6 ↗.routingTable ↗.routes	xml	xml(“<routingTable/>”)
ualcmp.ipv6 ↗.routingTable ↗.forwarding	bool	false
ualcmp.ipv6 ↗.routingTable ↗.isRouter	bool	this.forwarding
ualcmp.ipv6 ↗.routingTable ↗.multicastForwarding	bool	false
ualcmp.ipv6 ↗.routingTable ↗.useAdminDist	bool	false	Use Cisco-like administrative distances
ualcmp.ipv6 ↗.routingTable ↗.advManagedFlag	bool	false	“Managed address configuration” (M) flag in RAs
ualcmp.ipv6 ↗.routingTable ↗.advOtherConfigFlag	bool	false	“Other configuration” (O) flag in RAs
ualcmp.ipv6 ↗.routingTable ↗.advLinkMtu	int	1280	MTU option in RAs (1280 = IPv6 minimum MTU, 0 = don’t include)
ualcmp.ipv6 ↗.routingTable ↗.advCurHopLimit	int	30	Cur Hop Limit field in RAs (0 = unspecified)
ualcmp.ipv6 ↗.routingTable ↗.advDefaultLifetime	double	-1s	Router Lifetime in RAs (-1 = auto: 3*maxRtrAdvInterval)
ualcmp.ipv6 ↗.up ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.up ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.ipv6 ↗.up ↗.forwardServiceRegistration	bool	true
ualcmp.ipv6 ↗.up ↗.forwardProtocolRegistration	bool	true
ualcmp.ipv6 ↗.up ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.ipv6 ↗.up ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.ipv6 ↗.up ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.ipv6 ↗.icmpv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.icmpv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv6 ↗.icmpv6 ↗.checksumMode	string	“declared”
ualcmp.ipv6 ↗.icmpv6 ↗.mldModule	string	“”	Path to the MLD module, or “” if MLD is not enabled; MLD messages are dropped when empty
ualcmp.ipv6 ↗.lp ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.lp ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.ipv6 ↗.lp ↗.forwardServiceRegistration	bool	true
ualcmp.ipv6 ↗.lp ↗.forwardProtocolRegistration	bool	true
ualcmp.ipv6 ↗.lp ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.ipv6 ↗.lp ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.ipv6 ↗.lp ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.ipv6 ↗.neighbourDiscovery ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.neighbourDiscovery ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv6 ↗.neighbourDiscovery ↗.checksumMode	string	“declared”
ualcmp.ipv6 ↗.neighbourDiscovery ↗.icmpv6Module	string
ualcmp.ipv6 ↗.neighbourDiscovery ↗.mipv6Module	string
ualcmp.ipv6 ↗.neighbourDiscovery ↗.routingTableModule	string
ualcmp.ipv6 ↗.neighbourDiscovery ↗.minIntervalBetweenRAs	double	200s	RFC 4861: MinRtrAdvInterval (0.33 * MaxRtrAdvInterval)
ualcmp.ipv6 ↗.neighbourDiscovery ↗.maxIntervalBetweenRAs	double	600s	RFC 4861: MaxRtrAdvInterval
ualcmp.ipv6 ↗.neighbourDiscovery ↗.advReachableTime	double	3600s	advertised reachable time in RAs; hosts use it as base for NUD
ualcmp.ipv6 ↗.neighbourDiscovery ↗.dupAddrDetectTransmits	int	1	RFC 4862 Section 5.1: number of NS sent for DAD (0 = disable DAD)
ualcmp.ipv6 ↗.neighbourDiscovery ↗.optimisticDad	bool	false	RFC 4429 Optimistic DAD: if true, an autoconfigured address may be used as a source address while DAD is still in progress; if false (RFC 4862), packets that would use it are deferred until DAD completes
ualcmp.ipv6 ↗.neighbourDiscovery ↗.detectL2Movement	bool	true	if true (default), (re)start Router Discovery (send Router Solicitations) whenever an interface associates at the link layer (e.g. a wireless handover to a new access point); lets a mobile node detect movement and obtain a new care-of address immediately, instead of relying on frequent unsolicited Router Advertisements (cf. MIPv6 fast RAs). Set to false to restore the legacy behaviour (movement detected only from periodic Router Advertisements)
ualcmp.ipv6 ↗.neighbourDiscovery ↗.retransTimer	double	1s	RFC 4861 Section 10: delay between retransmitted NS messages
ualcmp.ipv6 ↗.neighbourDiscovery ↗.baseReachableTime	double	30s	RFC 4861 Section 10: base value for computing random ReachableTime
ualcmp.ipv6 ↗.neighbourDiscovery ↗.routerBootupTime	double	uniform(0s, 0.3s)	random startup delay before a router assigns its link-local address; routers boot faster than hosts so that RAs are available by the time hosts solicit
ualcmp.ipv6 ↗.neighbourDiscovery ↗.hostBootupTime	double	uniform(0.4s, 1s)	random startup delay before a host assigns its link-local address
ualcmp.ipv6 ↗.ipv6 ↗.displayStringTextFormat	string	“{ipv6StatusText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.ipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv6 ↗.ipv6 ↗.routingTableModule	string
ualcmp.ipv6 ↗.ipv6 ↗.ipv6NeighbourDiscoveryModule	string
ualcmp.ipv6 ↗.ipv6 ↗.icmpv6Module	string
ualcmp.ipv6 ↗.ipv6 ↗.procDelay	double	0s
ualcmp.ipv6 ↗.ipv6 ↗.sendRedirects	bool	true	RFC 4861 Section 8.2: when a router forwards a packet back out the interface it arrived on, send the source an ICMPv6 Redirect. Disable on wireless multi-hop / ad-hoc networks (e.g. MANET routing), where the geographic next hop is not directly reachable by the source, so redirects are useless and trigger a storm.
ualcmp.ipv6 ↗.ipsec ↗.displayStringTextFormat	string	“IN: ACCEPT: {inAccept} DROP: {inDrop} BYPASS: {inBypass}\n OUT: PROTECT: {outProtect} DROP: {outDrop} BYPASS: {outBypass}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.ipsec ↗.interfaceTableModule	string
ualcmp.ipv6 ↗.ipsec ↗.spdModule	string	“^.spd”
ualcmp.ipv6 ↗.ipsec ↗.sadModule	string	“^.sad”
ualcmp.ipv6 ↗.ipsec ↗.spdConfig	xml
ualcmp.ipv6 ↗.ipsec ↗.defaultProtection	string	“”	If not “”: value to use where <Protection> element is absent from the configuration
ualcmp.ipv6 ↗.ipsec ↗.defaultEspMode	string	“”	If not “”: value to use where <EspMode> element is absent from the configuration
ualcmp.ipv6 ↗.ipsec ↗.defaultEncryptionAlg	string	“”	If not “”: value to use where <EncryptionAlg> element is absent from the configuration
ualcmp.ipv6 ↗.ipsec ↗.defaultAuthenticationAlg	string	“”	If not “”: value to use where <defaultAuthenticationAlg> element is absent from the configuration
ualcmp.ipv6 ↗.ipsec ↗.defaultMaxTfcPadLength	int	0	Value to use where <MaxTfcPadLength> element is absent from the configuration
ualcmp.ipv6 ↗.ipsec ↗.ahProtectOutDelay	double	0.0s
ualcmp.ipv6 ↗.ipsec ↗.ahProtectInDelay	double	0.0s
ualcmp.ipv6 ↗.ipsec ↗.espProtectOutDelay	double	0.0s
ualcmp.ipv6 ↗.ipsec ↗.espProtectInDelay	double	0.0s
ualcmp.ipv6 ↗.spd ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.sad ↗.displayStringTextFormat	string	“entries: {numEntries}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.mipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.mipv6 ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.ipv6 ↗.mipv6 ↗.ipv6NeighbourDiscoveryModule	string
ualcmp.ipv6 ↗.mipv6 ↗.bindingUpdateListModule	string
ualcmp.ipv6 ↗.mipv6 ↗.bindingCacheModule	string
ualcmp.ipv6 ↗.mipv6 ↗.isHomeAgent	bool
ualcmp.ipv6 ↗.mipv6 ↗.isMobileNode	bool
ualcmp.ipv6 ↗.mipv6 ↗.maxHaBindingLifeTime	double	3600s	max binding lifetime for HA registration
ualcmp.ipv6 ↗.mipv6 ↗.maxRrBindingLifeTime	double	420s	max binding lifetime for CN (route optimization)
ualcmp.ipv6 ↗.mipv6 ↗.useRouteOptimization	bool	true	whether a mobile node route-optimizes with correspondent nodes (RFC 3775); if false, their traffic always uses the bidirectional home-agent tunnel
ualcmp.ipv6 ↗.buList ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.bindingCache ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.pmipv6 ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.pmipv6 ↗.interfaceTableModule	string		path to the InterfaceTable module
ualcmp.ipv6 ↗.pmipv6 ↗.ipv6NeighbourDiscoveryModule	string		path to the Ipv6NeighbourDiscovery module
ualcmp.ipv6 ↗.pmipv6 ↗.isLocalMobilityAnchor	bool	false	(the IPv6 routing table is resolved automatically)
ualcmp.ipv6 ↗.pmipv6 ↗.isMobileAccessGateway	bool	false
ualcmp.ipv6 ↗.pmipv6 ↗.localMobilityAnchorAddress	string	“”	MAG: the address of the LMA to register mobile nodes with
ualcmp.ipv6 ↗.pmipv6 ↗.mobileNodeProfiles	xml	xml(“<mobileNodes/>”)	MAG: mobile-node policy profiles, one per access interface, e.g. <mobileNodes> <mobileNode accessInterface=”wlan0” id=”mn1@example.com” homeNetworkPrefix=”2001:db8:1::” prefixLength=”64”/> </mobileNodes> (accessInterface may be omitted to match any access interface)
ualcmp.ipv6 ↗.pmipv6 ↗.bindingLifetime	double	3600s	lifetime requested in Proxy Binding Updates
ualcmp.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvValidLifetime	double	3600s	MAG: valid lifetime of the advertised home network prefix
ualcmp.ipv6 ↗.pmipv6 ↗.homeNetworkPrefixAdvPreferredLifetime	double	1800s	MAG: preferred lifetime of the advertised home network prefix
ualcmp.ipv6 ↗.mld ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.ipv6 ↗.mld ↗.interfaceTableModule	string		path to the InterfaceTable module
ualcmp.ipv6 ↗.mld ↗.routingTableModule	string		path to the Ipv6RoutingTable module
ualcmp.ipv6 ↗.mld ↗.checksumMode	string	“declared”	how the ICMPv6 checksum is handled
ualcmp.ipv6 ↗.mld ↗.enabled	bool	true	when false, MLD is inert on this node (see above)
ualcmp.ipv6 ↗.mld ↗.unsolicitedReportInterval	double	10s	host: delay before the repeated Report after a join
ualcmp.ipv6 ↗.mld ↗.robustnessVariable	int	2	loss tolerance; only supplies the defaults of the three params marked (RV) below
ualcmp.ipv6 ↗.mld ↗.queryInterval	double	125s	querier: interval between periodic General Queries
ualcmp.ipv6 ↗.mld ↗.queryResponseInterval	double	10s	querier: max delay a host may wait before answering a General Query
ualcmp.ipv6 ↗.mld ↗.multicastListenerInterval	double	(robustnessVariable * queryInterval) + queryResponseInterval	querier: how long a group stays “has listeners” without a new Report (RV)
ualcmp.ipv6 ↗.mld ↗.startupQueryInterval	double	queryInterval / 4	querier: interval between the initial General Queries at startup
ualcmp.ipv6 ↗.mld ↗.startupQueryCount	int	robustnessVariable	querier: number of General Queries sent at startup (RV)
ualcmp.ipv6 ↗.mld ↗.lastListenerQueryInterval	double	1s	querier: interval between the group-specific Queries sent after a Done
ualcmp.ipv6 ↗.mld ↗.lastListenerQueryCount	int	robustnessVariable	querier: number of group-specific Queries sent after a Done (RV)
ualcmp.ualcmpApp.binderModule	string	“binder”
ualcmp.ualcmpApp.serviceName	string	“Ualcmp”
ualcmp.ualcmpApp.requestQueueSize	int	0
ualcmp.ualcmpApp.subscriptionQueueSize	int	0
ualcmp.ualcmpApp.localAddress	string	“”	Local address; may be left empty (“”)
ualcmp.ualcmpApp.localPort	int	1000	localPort number to listen on
ualcmp.ualcmpApp.requestServiceTime	double	5us
ualcmp.ualcmpApp.subscriptionServiceTime	double	10us
ualcmp.ualcmpApp.serverThreadClass	string	“simu5g.mec.platform.services.base.SocketManager”
ualcmp.ualcmpApp.tos	int	-1	If not -1, set the Type of Service (IPv4) / Traffic Class (IPv6) field of sent packets to this value
ualcmp.udp ↗.displayStringTextFormat	string	“passed up: {numPassedUp} pks\nsent: {numSent} pks{udpDroppedText}”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.udp ↗.interfaceTableModule	string		The path to the InterfaceTable module
ualcmp.udp ↗.checksumMode	string	“declared”
ualcmp.udp ↗.defaultMulticastLoop	bool	true
ualcmp.tcp ↗.displayStringTextFormat	string	“”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.tcp ↗.checksumMode	string	“declared”
ualcmp.tcp ↗.advertisedWindow	int	14 * this.mss	In bytes, corresponds with the maximal receiver buffer capacity (Note: normally, NIC queues should be at least this size)
ualcmp.tcp ↗.delayedAcksEnabled	bool	false	Delayed ACK algorithm (RFC 1122) enabled/disabled
ualcmp.tcp ↗.nagleEnabled	bool	true	Nagle’s algorithm (RFC 896) enabled/disabled
ualcmp.tcp ↗.limitedTransmitEnabled	bool	false	Limited Transmit algorithm (RFC 3042) enabled/disabled (can be used for TcpReno/TcpTahoe/TcpNewReno/TcpNoCongestionControl)
ualcmp.tcp ↗.increasedIWEnabled	bool	false	Increased Initial Window (RFC 3390) enabled/disabled
ualcmp.tcp ↗.sackSupport	bool	false	Selective Acknowledgment (RFC 2018, 2883, 3517) support (header option) (SACK will be enabled for a connection if both endpoints support it)
ualcmp.tcp ↗.windowScalingSupport	bool	false	Window Scale (RFC 1323) support (header option) (WS will be enabled for a connection if both endpoints support it)
ualcmp.tcp ↗.windowScalingFactor	int	-1	Window Scaling Factor given as a shift count. Valid values are 0..14, and -1 for automatic selection (it chooses the smallest shift count that makes advertisedWindow representable in 16 bits)
ualcmp.tcp ↗.timestampSupport	bool	false	Timestamps (RFC 1323) support (header option) (TS will be enabled for a connection if both endpoints support it)
ualcmp.tcp ↗.mss	int	536	Maximum Segment Size (header option). Default 536 per RFC 1122.
ualcmp.tcp ↗.msl	int	120s	Maximum Segment Lifetime
ualcmp.tcp ↗.tcpAlgorithmClass	string	“TcpReno”
ualcmp.tcp ↗.dupthresh	int	3	Used for TcpTahoe, TcpReno, and SACK (RFC 3517) DO NOT change unless you really know what you are doing
ualcmp.tcp ↗.initialSsthresh	int	0xFFFFFFFF	Initial value for Slow Start threshold used in TahoeRenoFamily. The initial value of ssthresh SHOULD be set arbitrarily high (e.g., to the size of the largest possible advertised window) Without user interaction there is no limit…
ualcmp.tcp ↗.stopOperationExtraTime	double	0s	Extra time after lifecycle stop operation finished
ualcmp.tcp ↗.stopOperationTimeout	double	2s	Timeout value for lifecycle stop operation
ualcmp.tcp ↗.ecnWillingness	bool	false	True if willing to use ECN
ualcmp.tcp ↗.dctcpGamma	double	0.0625	A fixed estimation gain for calculating dctcp_alpha (RFC 8257 4.2)
ualcmp.tcp ↗.pmtudEnabled	bool	false	Path MTU Discovery (RFC 1191, RFC 1981) enabled/disabled
ualcmp.tcp ↗.pmtudTimeout	double	600s	Time after which the original MSS is restored to probe for increased path MTU (RFC 1191, Section 6.3)
ualcmp.at ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.at ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.at ↗.forwardServiceRegistration	bool	true
ualcmp.at ↗.forwardProtocolRegistration	bool	true
ualcmp.at ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.at ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.at ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.tn ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.tn ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.tn ↗.forwardServiceRegistration	bool	true
ualcmp.tn ↗.forwardProtocolRegistration	bool	true
ualcmp.tn ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.tn ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.tn ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
ualcmp.nl ↗.displayStringTextFormat	string	“processed {numProcessedPackets} pk ({processedTotalLength})”	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
ualcmp.nl ↗.interfaceTableModule	string		Module path to the InterfaceTable ↗ module
ualcmp.nl ↗.forwardServiceRegistration	bool	true
ualcmp.nl ↗.forwardProtocolRegistration	bool	true
ualcmp.nl ↗.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {“eth0”: “bridging”}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
ualcmp.nl ↗.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ethernetmac”: “bridging”}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
ualcmp.nl ↗.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {“ipv4”: “bridging”}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default

Source code¶

//
// Two ~gNodeB cells, each on an intermediate ~Upf of its own with a ~MecHost hung
// off it, so every cell has its own MEC host. Both intermediate ~Upf nodes meet
// at the anchor ~Upf, which carries the ~Ualcmp and, behind it, the
// ~MecOrchestrator. An X2 link joins the two gNodeBs. numUe ~NrUe terminals
// attach, and numBgCells ~BackgroundCell cells can be added as interferers.
//
network MultiMecHost
{
    parameters:
        // The gNBs connect to a 5GC (Upf), so every cellular stack has SDAP:
        // TS 37.324 ties SDAP to the 5GC connection, not to the radio
        **.cellularNic.hasSdap = default(true);
        int numUe = default(1);
        int numBgCells = default(0);
        @display("i=block/network2;bgb=1088,678;bgi=background/pisa");
    submodules:
        channelControl: LteChannelControl {
            @display("p=50,25;is=s");
        }
        routingRecorder: RoutingTableRecorder {
            @display("p=50,75;is=s");
        }
        configurator: Ipv4NetworkConfigurator {
            @display("p=50,125;is=s");
        }
        binder: Binder {
            @display("p=50,175;is=s");
        }
        coreControl: CoreControl {
            @display("p=50,375;is=s");
        }
        bearerConfigurator: BearerConfigurator {
            @display("p=50,225;is=s");
        }
        carrierAggregation: CarrierAggregation {
            @display("p=50,275;is=s");
        }
        upf: Upf {
            @display("p=500,131");
        }
        iUpf1: Upf {
            @display("p=390,247");
        }
        iUpf2: Upf {
            @display("p=603,247");
        }
        gnb1: gNodeB {
            @display("p=250,395;is=vl");
        }
        gnb2: gNodeB {
            @display("p=749,400;is=vl");
        }
        bgCell[numBgCells]: BackgroundCell {
            @display("p=250,577;is=vl");
        }
        ue[numUe]: NrUe {
            @display("p=500,481");
        }

        //# MEC modules
        mecHost1: MecHost {
            @display("p=248,247");
        }
        mecHost2: MecHost {
            @display("p=748,247");
        }
        mecOrchestrator: MecOrchestrator {
            @display("p=250,73");
        }
        ualcmp: Ualcmp {
            @display("p=390,73");
        }

    connections:

        //# 5G Core Network connections
        upf.pppg++ <--> Eth10G <--> iUpf1.pppg++;
        upf.pppg++ <--> Eth10G <--> iUpf2.pppg++;
        iUpf1.pppg++ <--> Eth10G <--> gnb1.ppp;
        iUpf2.pppg++ <--> Eth10G <--> gnb2.ppp;

        //# MEC-related connections
        ualcmp.ppp++ <--> Eth10G <--> upf.dnPppg;
        ualcmp.toMecOrchestrator --> mecOrchestrator.fromUALCMP;
        ualcmp.fromMecOrchestrator <-- mecOrchestrator.toUALCMP;
        mecHost1.ppp++ <--> Eth10G <--> iUpf1.pppg++;
        mecHost2.ppp++ <--> Eth10G <--> iUpf2.pppg++;

        //# X2 connections
        gnb1.x2++ <--> Eth10G <--> gnb2.x2++;
}

File: simulations/nr/mec/multiMecHost/MultiMecHost.ned